1984 Austin Mini Mayfair

Registration plate incorrect front and rear (0.1 (c))

Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b))

Nearside Front Hydraulic brake calliper insecurely mounted upper bolt securing washer missing (1.1.16 (c) (i))

Nearside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Front Upper Suspension arm pin or bush worn but not resulting in excessive movement inner pin (5.3.4 (a) (i))

Steering system slightly rough (2.1.1 (a))

All position lamps not working (4.2.1 (a))

Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a))

Nearside Headlamp aim too high (4.1.2 (a))

Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Rear fog lamp missing (4.5.1 (a) (ii))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

wiper blades in poor condition

Body has a sharp edge caused by damage passenger door (6.1.C.1)

Rear fog lamp not working (1.3.2b)

wiper blades in poor condition

Exhaust has a minor leak of exhaust gases (7.1.2)

Rear registration plate delaminated but not likely to be misread (6.3.1d)

clutch pedal rubber misssing

exhaust poorly mounted

front exhaust support bolt missing

All position lamps not working (1.1.A.3b)

Brake hose twisted (found during steering lock to lock check) nearside front (2.2.D.2b)

Exhaust emissions carbon monoxide content excessive (7.3.B.1a)

Front suspension ball joint dust cover insecure so that it no longer prevents the ingress of dirt both front inner knuckle joints (2.4.G.2)

Front suspension has excessive play in a lower suspension ball joint both (2.5.B.1a)

Hazard warning lamps inoperative (1.4.B.1b)

Nearside Headlamp aim too low (1.8)

Offside Front Front wheel bearing rough when rotated (2.5.A.2)

Offside Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt knuckle ioint (2.4.G.2)

Offside Lower Front suspension has excessive movement at a suspension ball joint insecure in hub (2.5.A.1c)

Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Subframe mounting prescribed area is excessively corroded rear (2.4.A.3)

Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)

Registration plate lamp not working both (1.1.C.1d)

Speedometer cannot be illuminated. (6.7.3)

Windscreen washer provides insufficient washer liquid (8.2.3)

clutch pedal rubber missing

exhaust poorly mounted

Front Exhaust has a minor leak of exhaust gases (7.1.2)

front exhaust support bracket insecure

registration plate delaminated but not likely to be misread (6.3.1d)

Brake pipe excessively corroded (3.6.B.2c)

Hazard warning switch faulty (1.4.B.1d)

Nearside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Front Upper Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Steering rack gaiter split (2.2.D.2d)

Offside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Front Upper Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Steering rack gaiter split (2.2.D.2d)

Offside Front constant velocity joint gaiter insecurely mounted to its housing (2.5.C.1a)

Front Exhaust has a major leak of exhaust gases (7.1.2)

Front Exhaust system not adequately supported (7.1.1)

Offside Outer Front constant velocity joint gaiter insecurely mounted to its housing (2.5.C.1a)

Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)