MOT Status
ExpiredMileage
183,549 miSignificantly above average — investigate
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Nearside Rear Anti-roll bar damaged but not seriously weakened (5.3.3 (b) (i))
Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Battery insecure and likely to fall from carrier (4.13 (a) (ii))
Exhaust has a major leak of exhaust gases (6.1.2 (a))
Front Windscreen wiper does not clear the windscreen effectively Both (3.4 (b) (ii))
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded Under wheel arch/inner wing (1.1.21 (e) (i))
Offside Headlamp aim too high (4.1.2 (a))
Offside Headlamp not working on main beam (4.1.1 (a) (ii))
Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))
Coolant leak ()
Nearside Front Standard fitment seat belt missing ()
Nearside Rear Nail in tyre ()
Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Offside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Nearside rear brake recording little or no effort (3.7.B.5a)
Offside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Nearside Front Shock absorber has a light misting of oil (2.7.3)
Nearside Front Tyre worn close to the legal limit (4.1.E.1)
Vehicle structure has slight corrosion (6.1.B.2)
previous welding repairs heavily undersealed
Brake master cylinder/servo mounting prescribed area is excessively corroded (3.6.C.3)
Driver's seat fore and aft adjustment mechanism not functioning as intended. (6.2.A.3)
Driver's seat insecure (6.2.A.1)
Horn not working (1.6.2a)
Nearside Front Seat belt retracting mechanism defective (5.2.5b)
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing (6.1.B.2)
Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b)
Nearside Rear Suspension spring mounting prescribed area is excessively corroded floor (2.4.A.3)
Nearside Rear Suspension spring mounting prescribed area is excessively corroded inner wing (2.4.A.3)
Nearside Registration plate lamp not working (1.1.C.1d)
Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Nearside rear parking brake recording little or no effort (3.7.B.6a)
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing (several places) (6.1.B.2)
Offside Headlamp aim too low (1.8)
Offside Rear Anti-roll bar rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)
Offside Rear Suspension spring mounting prescribed area is excessively corroded outrigger (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is excessively corroded outrigger (front spring mounting area) (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is excessively corroded outrigger (rear of spring mounting area) (2.4.A.3)
Offside Registration plate lamp not working (1.1.C.1d)
Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Parking brake: efficiency below requirements (3.7.B.7)
Service brake: efficiency below requirements (3.7.B.7)
Front Vehicle structure has slight corrosion / rear (6.1.B.2)
Nearside Front Shock absorber has a light misting of oil (2.7.3)
Nearside Front Tyre worn close to the legal limit (4.1.E.1)
Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive floor (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive inner wing (2.4.A.3)
Front Vehicle structure has slight corrosion (6.1.B.2)
Nearside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Front Vehicle structure has slight corrosion (6.1.B.2)
Offside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Vehicle structure has slight corrosion (6.1.B.2)
Rear Vehicle structure has slight corrosion (6.1.B.2)
Brakes imbalanced across an axle (3.7.B.5b)
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside Rear position lamp(s) has less than 50% of the light sources illuminating (1.1.A.3b)
Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside front parking brake recording little or no effort (3.7.B.6a)
Offside Front Brake pipe excessively corroded (3.6.B.2c)
Offside Front Suspension arm has excessive play in a ball joint (2.4.G.2)
Parking brake: efficiency below requirements (3.7.B.7)
Rear front brake application uneven (3.7.B.2)
Registration plate lamp not working (1.1.C.1d)
Nearside Rear Mechanical brake component has restricted free movement (3.5.1k) DANGEROUS
Nearside Rear front brake binding (3.7.B.1) DANGEROUS
Front Vehicle structure has slight corrosion (6.1.B.2)
Nearside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Front Vehicle structure has slight corrosion (6.1.B.2)
Offside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Vehicle structure has slight corrosion (6.1.B.2)
Rear Vehicle structure has slight corrosion (6.1.B.2)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Vehicle structure has slight corrosion (6.1.A.1)
drivers door fouling front wing when being opened
side door not closeing into bottom catch
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside Registration plate lamp not working (1.1.C.1d)
Nearside front brake binding (3.7.B.1)
Nearside rear brake recording little or no effort (3.7.B.5a)
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded (3.6.C.3)
Offside Headlamp aim too low (1.8)
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Offside Registration plate lamp not working (1.1.C.1d)
Offside rear brake recording little or no effort (3.7.B.5a)
Offside rear parking brake recording little or no effort (3.7.B.6a)
Parking brake: efficiency below requirements (3.7.B.7) DANGEROUS
Service brake: efficiency below requirements (3.7.B.7) DANGEROUS
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Vehicle structure has slight corrosion (6.1.A.1)
drivers door fouling front wing when being opened
side door not closeing into bottom catch
Brake pipe slightly corroded (3.6.B.2c)
Nearside Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)
Offside Front Body has slight corrosion (6.1.B.2)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
Steering system slightly tight (2.2.D.1)
corrosion to rear chassis rails
Brake load sensing valve linkage obviously incorrectly adjusted (3.6.E.3)
Horn sounds harsh or grating (1.6.2e)
Nearside Front Body has excessive displacement which may lead to loss of vehicle control (6.1.B.1a)
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside Rear Body has a sharp edge caused by damage (6.1.C.1)
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside Rear Body or chassis is cracked, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside Registration plate lamp not working (1.1.C.1d)
Offside Front Body has excessive displacement which may lead to loss of vehicle control (6.1.B.1a)
Offside Front Direction indicator insecure (1.4.A.2b)
Offside Front position lamp(s) not working (1.1.A.3b)
Offside Headlamp aim too low (1.8)
Offside Rear Body or chassis is cracked, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Offside rear brake recording little or no effort (3.7.B.5a)
Parking brake: efficiency below requirements (3.7.B.7)
Brake pipe slightly corroded (3.6.B.2c)
Nearside Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)
Offside Front Body has slight corrosion (6.1.B.2)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
Steering system slightly tight (2.2.D.1)
corrosion to rear chassis rails
Nearside Front Brake pipe slightly corroded (3.6.B.2c)
Nearside Rear Leaf spring has a slightly deteriorated shackle pin rubber bush not resulting in excessive movement (2.4.B.2)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Rear Leaf spring has a slightly deteriorated shackle pin rubber bush not resulting in excessive movement (2.4.B.2)
n/s/f and o/s/f body mount rubbers worn
Nearside Rear Body has a sharp edge caused by damage (6.1.C.1)
Nearside Rear Brake pipe excessively corroded (3.6.B.2c)
Nearside Rear position lamp(s) incorrect colour (1.1.A.3e)
Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Nearside rear parking brake recording little or no effort (3.7.B.6a)
Offside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)
Offside Headlamp excessively deteriorated so that the light output is severely reduced (1.7.5a)
Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Parking brake: efficiency below requirements (3.7.B.7)
Rear Brake pipe excessively corroded (3.6.B.2c)
Service brake: efficiency below requirements (3.7.B.7)
Nearside Front Brake pipe slightly corroded (3.6.B.2c)
Nearside Rear Leaf spring has a slightly deteriorated shackle pin rubber bush not resulting in excessive movement (2.4.B.2)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Rear Leaf spring has a slightly deteriorated shackle pin rubber bush not resulting in excessive movement (2.4.B.2)
n/s/f and o/s/f body mount rubbers worn
Nearside Rear Brake pipe slightly corroded (3.6.B.2c)
Nearside Rear Leaf spring has slight wear in a shackle pin and/or bush (2.4.B.2)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Rear Leaf spring has slight wear in a shackle pin and/or bush (2.4.B.2)
Nearside Front Suspension arm has excessive play in a pin/bush (2.4.G.2)
Nearside Headlamp not working on main beam (1.7.5a)
Nearside Rear rear parking brake recording little or no effort (3.7.B.6a)
Nearside Registration plate lamp not working (1.1.C.1d)
Offside Front Suspension arm has excessive play in a pin/bush (2.4.G.2)
Offside Headlamp aim too low (1.8)
Offside Headlamp not working on main beam (1.7.5a)
Offside Registration plate lamp not working (1.1.C.1d)
Parking brake: efficiency below requirements (3.7.B.7)
Service brake: efficiency below requirements (3.7.B.7)
Nearside Rear Brake pipe slightly corroded (3.6.B.2c)
Nearside Rear Leaf spring has slight wear in a shackle pin and/or bush (2.4.B.2)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Rear Leaf spring has slight wear in a shackle pin and/or bush (2.4.B.2)
Brake load sensing valve has been disconnected and was fitted as standard (3.6.E.2)
Nearside Front position lamp(s) not working (1.1.A.3b)
Nearside Rear Tie bar/rod has excessive play in a pin/bush (2.4.G.2)
Nearside Rear position lamp(s) incomplete (1.1.4a)
Offside Front position lamp(s) not working (1.1.A.3b)
Offside Rear Tie bar/rod has excessive play in a pin/bush (2.4.G.2)
Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)
Registration plate lamp not working (1.1.5c)
Service brake: efficiency below requirements (3.7.B.7)
Offside Headlamp aim too low and too far to the left. (1.8)
Offside Headlamp not working on main beam (1.7.5a)
Offside Rear Leaf spring has excessive wear in a shackle pin and/or bush (2.4.B.2)
Bonnet retaining device ineffective (8.4.2)
Horn not working (1.6.2a)
Nearside Headlamp aim not tested (1.8.A.1c)
Nearside Headlamp not working on dipped beam (1.7.5a)
Nearside Headlamp not working on main beam (1.7.5a)
Nearside Rear Leaf spring has excessive wear in a shackle pin and/or bush (2.4.B.2)
Nearside Stop lamp excessively damaged so that it is not visible from a reasonable distance (1.2.1d)
Offside Front position lamp(s) not working (1.1.A.3b)
Offside Rear fog lamp not working (1.3.2b)
Offside Rear position lamp(s) excessively deteriorated so that it is not visible from a reasonable distance (1.1.A.3d)
Offside Stop lamp not working (1.2.1b)
Nearside Rear Leaf spring has slight wear in an anchor pin and/or bush (2.4.B.2)
Offside Rear Leaf spring has slight wear in an anchor pin and/or bush (2.4.B.2)
front body mountings worn
windscreen wiper operation slow
windscreen wipers do not self park
Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)
Nearside Front Lower Suspension arm has slight play in a pin/bush (2.4.G.2)
Nearside Headlamp aim too low (1.8)
Nearside Stop lamp not working (1.2.1b)
Offside Front Lower Suspension arm has slight play in a pin/bush (2.4.G.2)
Offside Headlamp aim too low (1.8)
Offside Rear Lower Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)
Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)
Nearside Front Lower Suspension arm has slight play in a pin/bush (2.4.G.2)
Offside Front Lower Suspension arm has slight play in a pin/bush (2.4.G.2)
Offside Rear Lower Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)
Front registration plate letter/figure incomplete (6.3.1c)
Nearside Front Direction indicator incomplete (1.5.A1b)
Nearside Front Headlamp not working on main beam (1.7.5a)
Nearside Front Windscreen washer provides insufficient washer liquid (8.2.3)
Nearside Rear Registration plate lamp flickers when tapped lightly by hand (1.1.5e)
Offside Front Headlamp not working on main beam (1.7.5a)
Offside Rear Registration plate lamp flickers when tapped lightly by hand (1.1.5e)
Nearside rear brake recording little or no effort (3.7.B.5a) DANGEROUS
Nearside rear parking brake recording little or no effort (3.7.B.6a) DANGEROUS
Offside rear brake recording little or no effort (3.7.B.5a) DANGEROUS
Parking brake: efficiency below requirements (3.7.B.7) DANGEROUS
Service brake: efficiency below requirements (3.7.B.7) DANGEROUS
How Reliable is the Iveco Camper?
Based on 3,255 MOT tests across 189 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
AD52 SFE is a 2003 Iveco Camper in White with a 2,800cc diesel engine. This vehicle has been through 25 MOT tests with a personal pass rate of 52%.
Across all 2003 Iveco Camper models, the average MOT pass rate is 73.8% with a typical mileage of 100,478 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Iveco Camper fails its MOT is parking brake: efficiency below requirements, accounting for 176 recorded failures. If you're considering buying AD52 SFE, it's worth having these areas checked by a mechanic before committing.
The Iveco Camper typically stays on UK roads for around 36 years. At 23 years old, this Iveco Camper is well into its expected lifespan but still has years ahead.
Frequently Asked Questions
How do I check the history of AD52 SFE?
You can check the full history of AD52 SFE by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was AD52 SFE registered?
AD52 SFE is a 2003 Iveco Camper, first registered on 4 February 2003.
Is AD52 SFE safe to buy?
The MOT history for AD52 SFE shows 25 tests with a 52% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does AD52 SFE have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on AD52 SFE. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.