2005 Ford Ranger

Exhaust emissions exceed manufacturer's specified limit (8.2.2.2 (a))

Nearside Direction indicator not working front and rear (4.4.1 (a) (ii))

Nearside Side repeater not working (4.4.1 (a) (ii))

Offside Rear Parking brake inoperative on one side (1.4.1 (a))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Windscreen washer provides insufficient washer liquid both and blades not tested for clearing (3.5 (a))

Anti-roll bar pin or bush likely to become detached both front broken (5.3.4 (a) (ii)) DANGEROUS

Service brake has no recorded effort at a wheel both rear (1.2.1 (a) (ii)) DANGEROUS

Tyre tread depth below requirements of 1.6mm both front 235/75x16 (5.2.3 (e)) DANGEROUS

Central Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Exhaust mounting defective front and rear (6.1.2 (a))

Headlamp lens slightly defective both (4.1.1 (b) (i))

Nearside Front Inner wing holed

Obligatory mirror slightly damaged both (3.3 (b) (i))

Offside Front Outer Drive shaft joint constant velocity boot severely deteriorated leaking grease (6.1.7 (g) (i))

Steering box has slight free play detected at steering wheel (2.3 (a) (i))

Tyre worn close to legal limit/worn on edge n/s/r 3mm o/s/r 2.2mm (5.2.3 (e))

Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security both mid body mounts (6.2.2 (d) (i))

Both front body mounts on crossmember badly corroded

Brake load sensing valve stiff

Exhaust mounting defective Centre and rear (6.1.2 (a))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Seat belt anchorage prescribed area is corroded but not considered excessive Both inner sills (7.1.1 (a) (i))

Nearside Rear Position lamp not working (4.2.1 (a) (ii))

Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Inner chassis at leaf spring front mounting (5.3.6 (a) (i))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Both front body mounts on crossmember badly corroded

Brake load sensing valve stiff

Exhaust mounting defective Centre and rear (6.1.2 (a))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Headlamp lens slightly defective (4.1.1 (b) (i))

Seat belt anchorage prescribed area is corroded but not considered excessive Both inner sills (7.1.1 (a) (i))

Central Exhaust mounting defective (6.1.2 (a))

Nearside Side repeater slightly discoloured (4.4.3 (a))

Offside Side repeater slightly discoloured (4.4.3 (a))

Rear Exhaust mounting defective (6.1.2 (a))

Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Central Exhaust mounting defective (6.1.2 (a))

Nearside Side repeater slightly discoloured (4.4.3 (a))

Offside Side repeater slightly discoloured (4.4.3 (a))

Rear Exhaust mounting defective (6.1.2 (a))

Brake load sensing valve stiff (1.1.17 (c) (i))

Central Exhaust mounting defective (6.1.2 (a))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Handbrake spring under vehicle broken

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis near to rear shock absorber and spring mount (5.3.6 (a) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Steering locking device missing Track rod end (2.1.3 (d))

Power steering fluid reservoir empty (2.1.5 (b) (ii))

Power steering inoperative (2.1.5 (c) (i))

Rear Brake hose ferrule excessively corroded (1.1.12 (f) (i))

Brake load sensing valve stiff (1.1.17 (c) (i))

Central Exhaust mounting defective (6.1.2 (a))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Handbrake spring under vehicle broken

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis near to rear shock absorber and spring mount (5.3.6 (a) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Lower Ball joint locking device missing

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

advise all steering and suspension components showing corrosion

Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

advise all steering and suspension components showing corrosion

advise surface corrosion on steering and suspension

Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Nearside Front Upper Suspension arm rubber bush deteriorated resulting in excessive movement wishbone (2.4.G.2)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Upper Suspension arm rubber bush deteriorated resulting in excessive movement wishbone (2.4.G.2)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Front Brake pipe slightly corroded (3.6.B.2c)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Exhaust emits an excessive level of metered smoke for a turbo charged engine (7.4.B.3b)

Nearside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Nearside Front Shock absorber has an excessively worn bush (2.7.4)

Nearside Rear Leaf spring fractured (2.4.B.1a)

Offside Front Shock absorber has an excessively worn bush (2.7.4)

front brake application uneven (3.7.B.2)

exhaust system heavy carbon biuld up