2009 Kia Rio

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid wheel cylinder (1.1.16 (b) (i))

Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement front (5.3.4 (a) (i))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Rear Service brake fluctuating, but not excessively (1.2.1 (e))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

front exhaust mounting bracket broken

Front Power steering pipe/hose slightly corroded (2.1.5 (g) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Front and Rear exhaust joints slightly corroded

Nearside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Nearside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Exhaust system joints corroded

Nearside Front Brake hose has slight corrosion to ferrules (3.6.B.4e)

Offside Front Brake hose has slight corrosion to ferrules (3.6.B.4e)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Tyre worn on inner edge

Nearside Front Track rod end ball joint has excessive play (2.2.B.1f)

Offside Rear Registration plate lamp not working (1.1.C.1d)

Exhaust system joints corroded

Nearside Front Brake hose has slight corrosion to ferrules (3.6.B.4e)

Offside Front Brake hose has slight corrosion to ferrules (3.6.B.4e)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Tyre worn on inner edge

Centre Front Brake pipe slightly corroded to rear (3.6.B.2c)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Front Headlamp aim too low (1.8)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

rear brakes slightly grabbing

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)