2003 Subaru Impreza

Emissions not tested test cancelled as lambda excessively high, exhaust leak at front (8.2.1.2 (d))

Exhaust has a major leak of exhaust gases front, all system deteriorated (6.1.2 (a))

Front Exhaust emissions likely to be affected by an exhaust leak lambda off the scale (8.2.1.1 (b))

Headlamp aim projected beam image is obviously incorrect no pattern (4.1.2 (c))

Nearside Front Headlamp lens seriously defective milky and damaged/cracked (4.1.1 (b) (ii))

Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch (7.1.1 (a) (i))

Offside Front Headlamp lens seriously defective milky (4.1.1 (b) (ii))

Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch (7.1.1 (a) (i))

Offside Rear Lower Macpherson strut corroded and seriously weakened spring mount (5.3.3 (b) (i))

Offside Stop lamp(s) not working (4.3.1 (a) (ii))

Windscreen wiper does not clear the windscreen effectively Near and Offside (3.4 (b) (ii))

Offside Rear Lower Suspension spring mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected spring mount (5.3.6 (a) (ii)) DANGEROUS

Brake hose slightly deteriorated Near and Offside, front and rear (1.1.12 (b) (ii))

Brake pipe corroded, covered in grease or other material ALL (1.1.11 (c))

Nearside Front Tyre worn close to legal limit/worn on edge BALD on the outer shoulder (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge worn on the shoulder(s) (5.2.3 (e))

Rear Suspension component mounting prescribed area is corroded but not considered excessive Near and Offside (5.3.6 (a) (i))

Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Offside Rear Wheel bearing slightly noisy (5.1.3 (b) (i))

Offside Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive Near and Offside (5.3.6 (a) (i))

Headlamp lens seriously defective Near and Offside (4.1.1 (b) (ii))

Nearside Front Service brake excessively binding (1.2.1 (f))

Nearside Rear Shock absorbers has a serious fluid leak (5.3.2 (b))

Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i))

Windscreen wiper does not clear the windscreen effectively Near and Offside standard (3.4 (b) (ii))

Offside Rear Wheel bearing slightly noisy (5.1.3 (b) (i))

Offside Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive Near and Offside (5.3.6 (a) (i))

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

exhaust some corrosion at joints

Rear Registration plate lamp not working (1.1.C.1d)

Nearside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Front Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

front number plate starting to distort

Rear Registration plate lamp not working (1.1.C.1d)

NSF WIPER POOR CONDTION

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)