2001 Peugeot 206

Coolant leak ()

Nearside Front Side repeater incorrect colour (4.4.3 (a))

Offside Front Coil spring fractured or broken (5.3.1 (b) (i))

Offside Front Position lamp not working (4.2.1 (a))

Coolant leak ()

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

n/s/f sidelight dim but working

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Nearside Front Wheel bolt(s) missing (4.2.A.1e)

Nearside Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Front Suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)

Service brake: efficiency below requirements (3.7.B.7)

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

gearbox oil level bung loose

n/s/f sidelight dim but working

exhaust corroded

Fuel tank insecure strap broken (7.2.1)

Nearside Brake pipe excessively corroded to o/s/r (3.6.B.2c)

Nearside Front Anti-roll bar has excessive play in a ball joint drop link (2.4.G.2)

Nearside Rear Brake pipe excessively corroded (3.6.B.2c)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Rear rear brake recording little or no effort (3.7.B.5a)

Offside Front Anti-roll bar has excessive play in a ball joint drop link (2.4.G.2)

Offside Front Brake pipe excessively corroded (3.6.B.2c)

Offside Rear Brake pipe excessively corroded to flexi (3.6.B.2c)

Offside Rear Registration plate lamp not working (1.1.C.1d)

Offside Rear rear brake recording little or no effort (3.7.B.5a)

Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)

Rear Exhaust system not adequately supported clamp (7.1.1)

exhaust corroded

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Suspension arm ball joint dust cover damaged, but preventing the ingress of dirt (2.4.G.2)

Oil leak

Front Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Rear Brake load sensing valve seized (3.6.E.3)

Rear Brake pipe excessively corroded (3.6.B.2c)

Nail in nearside rear tyre

Offside Front Suspension arm ball joint dust cover damaged, but preventing the ingress of dirt (2.4.G.2)

Oil leak

Exhaust has a minor leak of exhaust gases (7.1.2)

Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Nearside rear brake recording little or no effort (3.7.B.5a)

Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Registration plate lamp not working (1.1.C.1d)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Outer Front Brake pipe slightly corroded (3.6.B.2c)

Offside Outer Front Brake pipe slightly corroded (3.6.B.2c)

Suspension joint nearside lower dust cover split/missing

Suspension joint offside lower dust cover split/missing

Nearside Outer Front Brake pipe slightly corroded (3.6.B.2c)

Offside Outer Front Brake pipe slightly corroded (3.6.B.2c)

Suspension joint nearside lower dust cover split/missing

Suspension joint offside lower dust cover split/missing

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)