2003 Toyota Yaris

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Oil leak, but not excessive (8.4.1 (a) (i))

Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

corrosion around rear subframe mounts

Front Anti-roll bar linkage pin or bush excessively worn Both sides (5.3.4 (a) (i))

Front Headlamp has a product on the lens so that the light output is severely reduced Both (4.1.4 (b))

Front Position lamp not working Both (4.2.1 (a) (ii))

Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Supplementary restraint system warning lamp indicates a fault (7.1.6 (a))

Offside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Oil leak, but not excessive (8.4.1 (a) (i))

Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

corrosion around rear subframe mounts

Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement BOTH (5.3.4 (a) (i))

Front Headlamp has a product on the lens but not seriously reducing light output BOTH (4.1.4 (b))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Rear Tyre worn close to legal limit/worn on edge on limit (5.2.3 (e))

Offside Front Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Offside Rear Tyre worn close to legal limit/worn on edge On limit (5.2.3 (e))

Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

surface rust throughout underside

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Front coil spring broken (2.4.C.1a)

Nearside Headlamp aim too far to the right (1.8)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear coil spring broken (2.4.C.1a)

Parking brake: efficiency below requirements (3.7.B.7)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front position lamp(s) not working (1.1.A.3b)

Offside Front position lamp(s) not working (1.1.A.3b)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Headlamp aim too high (1.8)

Nearside Headlamp aim too high (1.8)

Rear Tyre worn close to the legal limit (4.1.E.1)

Windscreen washer provides insufficient washer liquid (8.2.3)

Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Brake pad(s) wearing thin (3.5.1g)

front anti-roll bar bushes deteriorating

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

FUEL FILLER NECK PIPES CORRODED

Fuel filler neck slightly corroded.

Rear registration plate deteriorated (6.3.1d)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)