2003 Ford Focus

Brake pipe corroded, covered in grease or other material both rear (1.1.11 (c))

Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))

Fuel Pipe/s corroded

Nearside Front Lower Suspension arm ball joint has slight play (5.3.4 (a) (i))

slight wear on front brake discs

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Hole in sill (5.3.6 (a) (i))

Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i))

Offside Rear Rear fog lamp not working (4.5.1 (a) (ii))

Offside Rear Stop lamp(s) adversely affected by the operation of another lamp Affected by position lamp (4.3.3 (b))

Oil leaking excessively from engine (8.4.1 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Fuel tank exhaust shield missing where fitted as original equipment creating a risk of fire (6.1.3 (e)) DANGEROUS

Front Brake disc worn, but not excessively Both front (1.1.14 (a) (i))

Fuel Pipe/s corroded Pipes going into fuel tank

Nearside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Brake pipe corroded, covered in grease or other material Both front to rear pipes (1.1.11 (c))

Rear Heat shield insecure

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

exhaust rear heat shied insecure

Front Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Front Coil spring corroded both side (5.3.1 (b) (i))

Front Oil leak, but not excessive (8.4.1 (a) (i))

Front Windscreen wiper blade defective both side (3.4 (b) (i))

Rear Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Rear Coil spring corroded both side (5.3.1 (b) (i))

Rear Fuel Pipe/s corroded

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Emissions unable to be completed (8.2.1.2 (d))

Front Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Front Coil spring corroded both side (5.3.1 (b) (i))

Front Oil leak, but not excessive (8.4.1 (a) (i))

Front Windscreen wiper blade defective both side (3.4 (b) (i))

Rear Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Rear Coil spring corroded both side (5.3.1 (b) (i))

Rear Fuel Pipe/s corroded

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Oil leak, but not excessive (8.4.1 (a) (i))

Offside Rear Fuel Pipe/s corroded

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Oil leak, but not excessive (8.4.1 (a) (i))

Offside Rear Fuel Pipe/s corroded

Offside Rear Fuel Pipe/s corroded

Rear Coil spring corroded both side (5.3.1 (b) (i))

Front Coil spring corroded both side and rear both side (5.3.1 (b) (i))

Front Oil leak, but not excessive (8.4.1 (a) (i))

Front Registration plate inscription illegible and rear (0.1 (b))

Front Windscreen washer provides insufficient washer liquid both side (3.5 (a))

Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii))

Nearside Rear Wheel bearing has excessive play and offside rear and rough when rotated (5.1.3 (a) (i))

Front Coil spring corroded both side and rear both side (5.3.1 (b) (i))

Front Oil leak, but not excessive (8.4.1 (a) (i))

Offside Rear Wheel bearing slightly noisy (5.1.3 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Central Front number plate is cracked

Central Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Offside Front tyre has slight sidewall damage

oil leak

Engine Oil leaks

Front registration plate delaminated but not likely to be misread (6.3.1d)

Oil leak

Rear registration plate deteriorated but not likely to be misread (6.3.1d)

Rear fog lamp not working (1.3.2b)

Offside Stop lamp not working (1.2.1b)

Rear registration plate deteriorated but not likely to be misread (6.3.1d)

Offside Headlamp aim aimed so that it dazzles other road users (1.8.A.1a)

Offside Rear fog lamp not working (1.3.2b)

Rear registration plate deteriorated but not likely to be misread (6.3.1d)

front brake discs worn

n/s door mirror broken

Nearside Stop lamp not working (1.2.1b)

front brake discs worn

n/s door mirror broken

NEARSIDE MIRROR CRACKED.

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Nearside Headlamp not working on dipped beam (1.7.5a)

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Windscreen has damage to the swept area in excess of a 40mm circle outside zone 'A' (8.3.1d)

Nearside Headlamp aim too high when the centre of the headlamp is below 850mm from the ground (1.6.B2)

Offside Headlamp aim too high when the centre of the headlamp is below 850mm from the ground (1.6.B2)

Offside Headlamp not working on dipped beam (1.7.5a)