MOT Status
ExpiredMileage
96,133 miSignificantly above average — investigate
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Brake load sensing valve linkage defective and function impaired valve seized (1.1.17 (a))
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing rusted and holed (5.3.6 (a) (i))
Nearside Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i))
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii))
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength axle mount rusted and holed (5.3.6 (a) (i))
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill rusted and holed (5.3.6 (a) (i))
Nearside Windscreen washer provides insufficient washer liquid (3.5 (a))
Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))
Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))
Offside Rear Position lamp not working (4.2.1 (a) (ii))
Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i))
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner/outer sill rusted and holed (5.3.6 (a) (i))
Rear Brake load sensing valve linkage defective and function impaired rusted away (1.1.17 (a))
Rear Brakes imbalanced across an axle (1.2.1 (b) (i))
Offside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS
Central Rear Upper Stop lamp(s) with a multiple light source up to 1/2 not functioning (4.3.1 (a) (i))
Nearside Rear Direction indicator slightly discoloured (4.4.3 (a))
Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))
both rear bump stops rusted away and missing
rear axle heavily rusted
Central Rear Upper Stop lamp(s) with a multiple light source up to 1/2 not functioning (4.3.1 (a) (i))
Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive inner wing (5.3.6 (a) (i))
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))
both rear bump stops missing/mounts rusted away
Brake load sensing valve linkage defective and function impaired (1.1.17 (a))
Drive shaft joint excessively worn (6.1.7 (c) (i))
Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))
Nearside Front Position lamp not working (4.2.1 (a) (ii))
Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i))
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii))
Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))
Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt clip loose? (6.1.7 (g) (ii))
Offside Front Upper Macpherson strut top bush or bearing has excessive wear or free play (5.3.4 (a) (i))
Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i))
Spare wheel insecure in carrier (6.1.5 (b) (i))
Central Rear Upper Stop lamp(s) with a multiple light source up to 1/2 not functioning (4.3.1 (a) (i))
Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive inner wing (5.3.6 (a) (i))
Nearside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))
both rear bump stops missing/mounts rusted away
Front Brake pad(s) wearing thin (1.1.13 (a) (ii))
Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))
Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Offside Front upper strut bearing assembly deteriorated
Rear Passenger seat(s) missing at time of test bench seat ()
Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))
both rear bump stops missing/rusted away
engine malfunction indicator lamp illuminated on dash
large engine oil leak
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))
Exhaust has a major leak of exhaust gases front downpipe/cat (6.1.2 (a))
Exhaust has a major leak of exhaust gases front link pipe (6.1.2 (a))
Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))
Nearside Rear Brake hose ferrule excessively corroded (1.1.12 (f) (i))
Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))
Offside Rear Brake hose ferrule excessively corroded (1.1.12 (f) (i))
Front Brake pad(s) wearing thin (1.1.13 (a) (ii))
Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))
Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Offside Front upper strut bearing assembly deteriorated
Rear Passenger seat(s) missing at time of test bench seat ()
Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))
both rear bump stops missing/rusted away
engine malfunction indicator lamp illuminated on dash
large engine oil leak
Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Nearside Front Tyre worn close to the legal limit (4.1.E.1)
Offside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
Rear Sub-frame corroded but not seriously weakened (2.4.G.1)
Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)
Hazard warning switch faulty (1.4.B.1d)
Nearside Front Lower Suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)
Nearside Rear Inner Subframe mounting prescribed area is excessively corroded (2.4.A.3)
Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)
Front Exhaust has a minor leak of exhaust gases (7.1.2)
Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Nearside Front Tyre worn close to the legal limit (4.1.E.1)
Offside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
Rear Sub-frame corroded but not seriously weakened (2.4.G.1)
Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)
Hazard warning switch faulty (1.4.B.1d)
Nearside Front Suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)
Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Offside Rear Nail in tyre ()
Items removed from driver's view prior to test ()
Nearside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)
Some damage to windscreen but not seriously affecting drivers view
Service brake: efficiency below requirements (3.7.B.7)
Front Brakes imbalanced across an axle By 50% (3.7.B.5b) DANGEROUS
Items removed from driver's view prior to test ()
Nearside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)
Some damage to windscreen but not seriously affecting drivers view
Exhaust has a minor leak of exhaust gases (7.1.2)
Nearside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)
Some damage to windscreen but not affecting drivers view
Nearside Front Tyre not fitted in accordance with side wall instructions (4.1.D.1f)
Offside Front Tyre not fitted in accordance with side wall instructions (4.1.D.1f)
Battery leaking electrolyte (1.9.1) DANGEROUS
Brake valve leaking (3.6.A.1) DANGEROUS
Offside Rear Suspension component mounting prescribed area is excessively corroded Inner & outer sill (2.4.A.3) DANGEROUS
Exhaust has a minor leak of exhaust gases (7.1.2)
Nearside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)
Some damage to windscreen but not affecting drivers view
Centre Front Exhaust has a minor leak of exhaust gases (7.1.2)
Nearside Front Anti-roll bar has excessive play in a pin/bush (2.4.G.2)
Offside Front Anti-roll bar has excessive play in a pin/bush (2.4.G.2)
Centre Front Exhaust has a minor leak of exhaust gases (7.1.2)
Offside Rear Brake load sensing valve stiff (3.6.E.3)
Nearside Front Tyre worn close to the legal limit (4.1.E.1)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)
Fuel tank insecure (7.2.1)
Nearside Battery leaking electrolyte (1.9.1)
Nearside Front Lower Suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)
Offside Rear Brake load sensing valve seized (3.6.E.3)
Offside Rear Tyre has ply or cords exposed (4.1.D.1b)
Nearside Front Anti-roll bar has slight play in a ball joint (2.4.G.2)
Brakes imbalanced across an axle (3.7.B.5b)
Rear Exhaust has part of the system excessively deteriorated (7.1.1a)
front discs rusted advise change
Nearside Front Shock absorber has a light misting of oil (2.7.3)
Front Exhaust has a major leak of exhaust gases (7.1.2)
Nearside Front Shock absorber has a light misting of oil (2.7.3)
Rear Brake load sensing valve linkage seized (3.6.E.3)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
Rear Exhaust has a minor leak of exhaust gases (7.1.2)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
Rear Brake load sensing valve linkage seized (3.6.E.3)
Rear Exhaust has a minor leak of exhaust gases (7.1.2)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
How Reliable is the Peugeot 206?
Based on 9,831,622 MOT tests across 644,158 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
BF02 HLM is a 2002 Peugeot 206 in Blue with a 1,124cc petrol engine. This vehicle has been through 28 MOT tests with a personal pass rate of 53.6%.
Across all 2002 Peugeot 206 models, the average MOT pass rate is 67.0% with a typical mileage of 65,592 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Peugeot 206 fails its MOT is tyre tread depth below requirements of 1.6mm, accounting for 446,851 recorded failures. If you're considering buying BF02 HLM, it's worth having these areas checked by a mechanic before committing.
The Peugeot 206 typically stays on UK roads for around 28 years. At 24 years old, this Peugeot 206 is approaching the upper end of the typical lifespan for this model.
Frequently Asked Questions
How do I check the history of BF02 HLM?
You can check the full history of BF02 HLM by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was BF02 HLM registered?
BF02 HLM is a 2002 Peugeot 206, first registered on 22 March 2002.
Is BF02 HLM safe to buy?
The MOT history for BF02 HLM shows 28 tests with a 53.6% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does BF02 HLM have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on BF02 HLM. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.