2007 Ford Ka

Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Central Front Lower Oil leak, but not excessive (8.4.1 (a) (i))

Front Lower Oil leak, but not excessive drive shaft seal (8.4.1 (a) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Nearside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Offside Front Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Child Seat fitted not allowing full inspection of adult belt ()

Rear Sub-frame pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security Sill (6.2.2 (d) (i))

Offside Rear Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security Sill (6.2.2 (d) (i))

Offside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Rear Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security Sill (6.2.2 (d) (i))

Offside Rear Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security Sill (6.2.2 (d) (i))

Nearside Front Bonnet release lever damaged.

Nearside Front Upper Macpherson strut pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Coolant leak ()

engine oil leak.

Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wing. (6.2.2 (d) (i))

Power steering component leaking switch. (2.1.5 (a))

Coolant leak ()

engine oil leak.

Offside Rear Shock absorbers has a serious fluid leak (5.3.2 (b))

Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Nearside Front Lower Suspension component attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i))

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement rear bush (2.4.G.2)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

registration plate deteriorated but not likely to be misread rear (6.3.1d)

Central Rear registration plate deteriorated but not likely to be misread (6.3.1d)

Offside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement rear bush (2.4.G.2)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Nearside Front Tyre tread depth below requirements of 1.6mm 165\65\r13t (4.1.E.1)

Nearside Rear coil spring broken (2.4.C.1a)

Central Rear registration plate deteriorated but not likely to be misread (6.3.1d)

Offside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement rear bush (2.4.G.2)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)