2010 Iveco Daily

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Offside Front Lower Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security under bonnet area (6.2.2 (d) (i))

Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

o s f inner sill and outer lower step area heavily corroding not within any prescribed areas

Nearside Front Lower Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting under bonnet area (6.2.2 (d) (i))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Offside Front Lower Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security under bonnet area (6.2.2 (d) (i))

Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

o s f inner sill and outer lower step area heavily corroding not within any prescribed areas

slight corrosion to underside including suspension components

slight corrosion to underside including suspension components

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Brake master cylinder/servo mounting prescribed area is inadequately repaired (1.1.21 (e) (i))

Electronic stability control warning lamp indicates a fault (7.12 (e))

Offside Front Integral body structure inadequately repaired such that structural rigidity is significantly reduced inner arch area (6.1.1 (d) (i))

slight corrosion to underside including suspension components

Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement New part fitted but has movement in the bar. (5.3.4 (a) (i))

Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Up in the wheel arch marked with chalk near mounting point . (6.2.2 (d) (i))

Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement New part fitted but has movement in the bar. (5.3.4 (a) (i))

Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement both (5.3.4 (a) (i))

Rear Inner Tyre worn close to legal limit/worn on edge both (5.2.3 (e))

Offside Front Service brake excessively binding (1.2.1 (f))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement both (5.3.4 (a) (i))

Rear Inner Tyre worn close to legal limit/worn on edge both (5.2.3 (e))

Nearside Front Headlamp aim too low (4.1.2 (a))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Horn not working (7.7 (a) (ii))

under tray

Front Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

under guards

Front Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Offside Front Headlamp aim too low and too far to the right. (1.8)

under guards

Brake warning device not working correctly (3.3.D.3a)

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Rear Registration plate lamp not working (1.1.C.1d)

Nearside Rear rear brake binding (3.7.B.1)

Rear Body insecure and dangerous to other road users tail board (6.1.B.1b)

Nearside Front Front wheel bearing rough when rotated (2.5.A.2)

Offside Front Upper Suspension arm has excessive play in a ball joint (2.4.G.2)

Offside Upper Front position lamp(s) not working (1.1.A.3b)

Nearside Inner Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Upper Ball joint has slight play (2.2.B.1f)

Nearside Front Headlamp aim too high and too far to the right. (1.8)

Offside Front Headlamp aim too high and too far to the right. (1.8)

Offside Front Upper Ball joint has slight play (2.2.B.1f)