2003 Peugeot 206

Emissions unable to be completed (8.2.1.2 (d))

Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b))

Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Headlamp aim unable to be tested (4.1.2 (b))

Nearside Brake master cylinder/servo mounting prescribed area is excessively corroded bulkhead (1.1.21 (e) (i))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis outrigger (5.3.6 (a) (i))

Nearside Headlamp lens seriously defective (4.1.1 (b) (ii))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength bulkhead behind strut turret (5.3.6 (a) (i))

Offside Headlamp lens seriously defective (4.1.1 (b) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Offside Side repeater incorrect colour (4.4.3 (a))

Driver's seat insecure (6.2.5 (a) (ii)) DANGEROUS

Brake disc worn, pitted or scored, but not seriously weakened both front (1.1.14 (a) (ii))

Nearside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))

Offside Track rod end ball joint has slight play advise replacement (2.1.3 (b) (i))

Parking brake performance only just met.

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Suspension component mounting prescribed area is corroded but not considered excessive both front chassis legs near subframe mountings (5.3.6 (a) (i))

brake pedal spongy

Brake disc worn, pitted or scored, but not seriously weakened both front on inside (1.1.14 (a) (ii))

Central Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Offside Front Track rod end ball joint has slight play (2.1.3 (b) (i))

Offside Rear Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Central Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Exhaust carbon monoxide content at idle exceeds manufacturer's specified limits (8.2.1.2 (b))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Rear Service brake excessively fluctuating both rear (1.2.1 (e))

Brake disc worn, pitted or scored, but not seriously weakened both front discs (1.1.14 (a) (ii))

Brake disc worn, pitted or scored, but not seriously weakened both rear discs (1.1.14 (a) (ii))

Brake pad(s) wearing thin both rear sets (1.1.13 (a) (ii))

Central Front Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Offside Front Track rod end ball joint has slight play (2.1.3 (b) (i))

Offside Rear Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Both front headlamp aims faint but present

Both front headlamp lens in poor condition

Brake disc worn, pitted or scored, but not seriously weakened FRONT AND REAR (1.1.14 (a) (ii))

Front Service brake fluctuating, but not excessively (1.2.1 (e))

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive FLOOR (5.3.6 (a) (i))

Nearside front and nearside rear brake pipes are slightly corroded

Emissions not tested OIL BELOW MINIMUM / EXHAUST BLOW (8.2.1.2 (d))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Exhaust has a major leak of exhaust gases MIDDLE TO REAR (6.1.2 (a))

Exhaust system insecure MIDDLE TO REAR (6.1.2 (a))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL (5.3.6 (a) (i))

Nearside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Both front headlamp lens in poor condition

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Headlamp aims faint but present

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive FLOOR (5.3.6 (a) (i))

Nearside front and rear brake pipes are slightly corroded but not excessive

Offside Front Tyre worn close to legal limit/worn on edge 2.2 mm (5.2.3 (e))

Oil leak, but not excessive SUMP PLUG AREA (8.4.1 (a) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Brake hose has slight corrosion to ferrule BOTH REAR FLEXYS (1.1.12 (f) (i))

Coil spring corroded BOTH FRONTS (5.3.1 (b) (i))

Front wipers are starting to smear the screen slightly

Headlamp aims faint but present

Middle to rear exhaust sections corroded not leaking

Nearside Front Tyre worn close to legal limit/worn on edge 2.7 mm (5.2.3 (e))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Rear seats missing time of test

Suspension arm corroded but not seriously weakened BOTH REAR ARMS (5.3.3 (b) (i))

Suspension arm pin or bush worn but not resulting in excessive movement BOTH REAR ARMS (5.3.4 (a) (i))

gearbox mount in poor condition

All direction indicators adversely affected by the operation of another lamp (4.4.3 (b))

Emissions not tested Oil below min and exhaust blow (8.2.1.2 (d))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Front Registration plate does not conform to the specified requirements (0.1 (d))

Fuel cap/sealing device ineffective Unable to open fuel cap to check seal (6.1.3 (b) (i))

Horn not working (7.7 (a))

Nearside Front Brake hose ferrule excessively corroded (1.1.12 (f) (i))

Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt outer (6.1.7 (g) (ii))

Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i))

Offside Front Brake hose ferrule excessively corroded (1.1.12 (f) (i))

Offside Front Brake pipe excessively corroded (1.1.11 (c))

Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i))

Oil leaking excessively from engine (8.4.1 (a) (i))

Rear Registration plate does not conform to the specified requirements (0.1 (d))

Aims faint but present

Brake fluid reservoir and servo damp no signs of a leak

Brake hose has slight corrosion to ferrule BOTH REARS (1.1.12 (f) (i))

Coil spring corroded BOTH FRONTS (5.3.1 (b) (i))

Gearbox mount in poor condition

Nearside Front Brake hose slightly twisted (1.1.12 (b) (i))

Nearside Front Tyre worn close to legal limit/worn on edge 2.7 mm / tread cracked (5.2.3 (e))

Nearside Rear Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Brake pipe corroded, covered in grease or other material both front to rear brake pipes (1.1.11 (c))

Exhaust has a major leak of exhaust gases At the front join and middle join of the exhaust (6.1.2 (a))

Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Brake pipe corroded, covered in grease or other material both front to rear brake pipes (1.1.11 (c))

Front Oil leak oil filter ()

Front Play in steering rack inner joint(s) ()

Front brake disc worn, pitted or scored, but not seriously weakened both front (3.5.1i)

Nearside Brake pipe slightly corroded front to rear (3.6.B.2c)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Rear position lamp(s) slightly affected by the operation of another lamp (1.1.A.3f)

Nearside Front Track rod end ball pin shank loose (2.2.B.1c)

Front Oil leak oil filter ()

Front Play in steering rack inner joint(s) ()

Front brake disc worn, pitted or scored, but not seriously weakened both front (3.5.1i)

Nearside Brake pipe slightly corroded front to rear (3.6.B.2c)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Rear position lamp(s) slightly affected by the operation of another lamp (1.1.A.3f)

Nearside Front Lower Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Nearside Front Suspension arm has excessive play in a pin/bearing front (2.4.G.2)

Nearside Rear Suspension component mounting prescribed area is excessively corroded exhaust mount (2.4.A.3)

Offside Front Suspension arm has excessive play in a pin/bearing front (2.4.G.2)

Offside Rear Registration plate lamp not working (1.1.C.1d)

Offside Rear brake caliper locking device insecure (3.5.1l)

Rear Exhaust has a major leak of exhaust gases exhaust box (7.1.2)

Rear registration plate character(s) not correctly formed (6.3.4b)

Front Oil leak oil filter ()

Front Play in steering rack inner joint(s) both ()

Front brake disc worn, pitted or scored, but not seriously weakened both (3.5.1i)

Nearside Brake pipe slightly corroded (3.6.B.2c)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Rear position lamp(s) slightly affected by the operation of another lamp (1.1.A.3f)

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Shock absorber has slight external damage to the casing (2.7.2a)

Nearside Front constant velocity joint is insecure (2.5.C.1b)

Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Rear Brake pad(s) wearing thin (3.5.1g)

Exhaust noisy (7.1.4)

Nearside Front coil spring corroded (2.4.C.1b)

Offside Front coil spring corroded (2.4.C.1b)

both rear shock absorber dust covers deteriorated

Nearside Rear Registration plate lamp not working (1.1.C.1d)

Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Front brake disc contaminated by grease (3.5.1h)

Exhaust noisy (7.1.4)

Nearside Front coil spring corroded (2.4.C.1b)

Offside Front coil spring corroded (2.4.C.1b)

both rear shock absorber dust covers deteriorated

Exhaust noisy (7.1.4)

Nearside Front Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)

Nearside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Exhaust noisy (7.1.4)

Nearside Front Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)

Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Rear Exhaust has part of the system slightly deteriorated (7.1.1a)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)