2007 Jaguar S-type

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

corrosion throughout vehicle. plastic under guards and sill covers fitted obscuring testable items

Oil leak, but not excessive (8.4.1 (a) (i))

Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

corrosion throughout vehicle .

Emissions unable to be completed due to extremely high co . may cause premature damage to analyser (8.2.1.2 (d))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Nearside Front Brake hose ferrule excessively corroded (1.1.12 (f) (i))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Rear Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Brake hose ferrule excessively corroded (1.1.12 (f) (i))

Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i))

Offside Rear Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i))

Nearside Seat belt anchorage prescribed area is corroded but not considered excessive outer sill (7.1.1 (a) (i))

Offside Front Service brake binding but not excessively (1.2.1 (f))

Oil leak, but not excessive (8.4.1 (a) (i))

Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

corrosion to sills , Plastic covers fitted.

Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Horn not working (7.7 (a))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Rear Suspension rod ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Rear Suspension rod ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

corrosion to sills , Plastic covers fitted.

Offside Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Offside Rear Service brake excessively binding (1.2.1 (f))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Offside Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) DANGEROUS

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Oil leak, but not excessive (8.4.1 (a) (i))

Offside Rear Lower Suspension arm has slight play in a pin/bush (2.4.G.2)

Offside Rear Lower Suspension arm has slight play in a pin/bush (2.4.G.2)

Nearside Front Tyre has a tear, caused by separation or partial failure of its structure (4.1.D.1b)

Nearside Headlamp aim too low (1.8)

Offside Rear Lower Suspension arm has slight play in a pin/bush (2.4.G.2)

Nearside Rear Lower Suspension arm has excessive play in a pin/bush (2.4.G.2)

Supplementary Restraint System warning lamp indicates a fault (5.4.2)

Nearside Front Tyre has a bulge, caused by separation or partial failure of its structure (4.1.D.1b) DANGEROUS

Nearside Front Torque/reaction arm has a slightly deteriorated rubber bush (2.4.G.2)

Offside Front Torque/reaction arm has a slightly deteriorated rubber bush (2.4.G.2)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

both front tyres worn low on inside edge

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)