2003 Hyundai Getz

Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i))

Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Front Outer Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Nearside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))

Nearside Rear Integral body structure is deformed but structural rigidity is not significantly reduced (6.1.1 (a) (i))

Offside Front Outer Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Offside Front Tyre fitted wrong way round to sidewall instruction

Offside Front Tyre worn close to legal limit/worn on edge Edge (5.2.3 (e))

Offside Headlamp has a product on the light source but not seriously reducing light output (4.1.4 (b))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced Sill (6.1.1 (c) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Stop lamp(s) non-obligatory stop lamp not working (4.3.1 (a) (ii))

Front Anti-roll bar linkage ball joint has slight play both sides (5.3.4 (a) (i))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement D bush (5.3.4 (a) (i))

Offside Rear Service brake fluctuating, but not excessively (1.2.1 (e))

Front Anti-roll bar linkage ball joint has slight play both sides (5.3.4 (a) (i))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement D bush (5.3.4 (a) (i))

Offside Rear Service brake fluctuating, but not excessively (1.2.1 (e))

Registration plate lamp inoperative in the case of a single lamp or all lamps both (4.7.1 (b) (ii))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Road wheel slightly distorted (5.2.2 (c) (i))

Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Stop lamp(s) not working (4.3.1 (a) (ii))

Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Road wheel slightly distorted (5.2.2 (c) (i))

Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement d-bushes (5.3.4 (a) (i))

Offside Rear Road wheel slightly distorted (5.2.2 (c) (i))

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i))

Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement d-bushes (5.3.4 (a) (i))

Offside Rear Road wheel slightly distorted (5.2.2 (c) (i))

Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b))

Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Road wheel badly distorted (5.2.2 (c) (i))

Offside Headlamp aim too low and too far to the right. (4.1.2 (a))

Nearside Front Road wheel slightly distorted (5.2.2 (c) (i))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Rear Service brake excessively binding (1.2.1 (f))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Nearside Rear Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Road wheel slightly distorted (5.2.2 (c) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Front Road wheel bead rim badly distorted (4.2.A.1a)

Nearside Stop lamp not working (1.2.1b)

Front Brake pad(s) wearing thin (3.5.1g)

Offside Front Tyre worn close to the legal limit inside edge low (4.1.E.1)

Fuel flap sticking on release