2005 Subaru Impreza

Nearside Front Inner Seat belt anchorage prescribed area is corroded but not considered excessive Sill/ floor (7.1.1 (a) (i))

Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive Sill (5.3.6 (a) (i))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive Sill (5.3.6 (a) (i))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Lower Suspension arm ball joint has slight play (5.3.4 (a) (i))

Nearside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Offside Front Inner Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

corrosion rear suspension components

inner sills corroding

Nearside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Stop lamp(s) not working (4.3.1 (a) (ii))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive sill (5.3.6 (a) (i))

Offside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Offside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive sill (5.3.6 (a) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Tyre worn close to the legal limit inner edge on nearside front (4.1.E.1)

Tyre worn close to the legal limit inner edge on offside fornt (4.1.E.1)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Brake pad(s) wearing thin (3.5.1g)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)