1986 Fiat Ducato

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced inner wing area (6.1.1 (c) (i))

Nearside Front Tyre slightly damaged/cracking or perishing 195/14c (5.2.3 (d) (ii))

Nearside Inner Integral body structure is corroded but structural rigidity is not significantly reduced sill area (6.1.1 (c) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Exhaust mounting defective x2 rubber rings (6.1.2 (a))

indicator tel tail inop

Nearside Rear Brakes imbalanced across an axle poss wheel cly seized (1.2.1 (b) (i))

Offside Front Direction indicator not working (4.4.1 (a) (ii))

Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Front Headlamp not working on main beam (4.1.1 (a) (ii))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Rear Exhaust has a major leak of exhaust gases box (6.1.2 (a))

Registration plate lamp does not illuminate simultaneously with the position lamps (4.7.2 (a))

Offside Rear Tyre has a tear, caused by separation or partial failure of its structure 185/r14c (5.2.3 (d) (ii)) DANGEROUS

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced inner wing area (6.1.1 (c) (i))

Nearside Front Tyre slightly damaged/cracking or perishing 195/14c (5.2.3 (d) (ii))

Nearside Inner Integral body structure is corroded but structural rigidity is not significantly reduced sill area (6.1.1 (c) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Exhaust mounting defective x2 rubber rings (6.1.2 (a))

indicator tel tail inop

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Exhaust has a minor leak of exhaust gases rear box (6.1.2 (a))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced inner wing area (6.1.1 (c) (i))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Rear lamp lens damaged

Rear Leaf spring has slight wear in a shackle pin and/or bush spring eye bushes both sides perished (5.3.4 (a) (i))

under body surface rust and unsealed

Offside Front Headlamp aim unable to be tested (4.1.2 (b))

Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Rear Brakes imbalanced across an axle (1.2.1 (b) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Rear Registration plate lamp does not illuminate simultaneously with the position lamps (4.7.2 (a))

Windscreen washer not working (3.5 (a))

Front Lower Suspension arm ball joint likely to become detached no locking device both sides (5.3.4 (a) (ii)) DANGEROUS

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Exhaust has a minor leak of exhaust gases rear box (6.1.2 (a))

Front Windscreen wiper blade defective (3.4 (b) (i))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced inner wing area (6.1.1 (c) (i))

Hazard warning lamps inoperative (4.4.1 (e))

Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i))

Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Headlamp not working on main beam (4.1.1 (a) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i))

Offside Stop lamp(s) not working (4.3.1 (a) (ii))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Windscreen washer not working (3.5 (a))

Windscreen wiper not working (3.4 (a))

Driver's seat insecure (6.2.5 (a) (ii)) DANGEROUS

Nearside Rear Tyre has ply or cords exposed sidewall perished/split (5.2.3 (d) (ii)) DANGEROUS

Passenger's seat insecure (6.2.6 (a) (ii)) DANGEROUS

Rear Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) DANGEROUS

Headlamp lens slightly defective both sides (4.1.1 (b) (i))

All direction indicators flashing less than 60 times a minute (4.4.4 (a))

Brake pipe corroded, covered in grease or other material all pipes, undersealed/coated (1.1.11 (c))

Nearside Rear Service brake binding but not excessively (1.2.1 (f))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive inner arch (5.3.6 (a) (i))

Offside Rear Leaf spring has slight wear in a shackle pin and/or bush (5.3.4 (a) (i))

Offside Rear Service brake binding but not excessively (1.2.1 (f))

Offside Rear Stop lamp(s) lens defective which has no effect on emitted light (4.3.1 (b) (i))

Rear Exhaust has a minor leak of exhaust gases silencer (6.1.2 (a))

Rear Exhaust mounting defective rubbers poor condition (6.1.2 (a))

front brake discs corroded

front seats fitted to swivel bases, seems alot of movement ?

oil leak

slight play n/s/f bottom ball joint

Exhaust system insecure (6.1.2 (a))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring mounting saddle (5.3.6 (a) (i))

Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/ floor (7.1.1 (a) (i))

Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i))

Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c))

Rear Brakes imbalanced across an axle (1.2.1 (b) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

front brake discs corroded

front seats fitted to swivel bases, seems alot of movement ?

oil leak

slight play n/s/f bottom ball joint

Exhaust emits blue smoke during acceleration (8.2.1.2 (g))

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Rear Service brake requirements only just met. It would appear that the braking system requires adjustment or repair (1.2.1 (c))

underside of vehicle shows signs of corrosion

Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i))

Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i))

Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i))

Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced bumper (6.1.1 (c) (i))

Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i))

Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i))

Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rear arch (6.1.1 (c) (i))

Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i))

Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced arch X2 (6.1.1 (c) (i))

Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced bumper (6.1.1 (c) (i))

Exhaust emits blue smoke during acceleration (8.2.1.2 (g))

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Rear Service brake requirements only just met. It would appear that the braking system requires adjustment or repair (1.2.1 (c))

underside of vehicle shows signs of corrosion

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Wheel bearing slightly noisy (5.1.3 (b) (i))

Offside Front Wheel bearing has slight play (5.1.3 (a) (i))

Various corrosion around corrosion on vehicle, both underside and top side.

Battery insecure and likely to fall from carrier (4.13 (a) (ii))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch. (5.3.6 (a) (i))

Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear cross member. (5.3.6 (a) (i))

Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Windscreen wiper does not clear the windscreen effectively Too slow. (3.4 (b) (ii))

Stop lamp(s) all not working (4.3.1 (a) (iii)) DANGEROUS

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Wheel bearing slightly noisy (5.1.3 (b) (i))

Offside Front Wheel bearing has slight play (5.1.3 (a) (i))

Stop lamp(s) switch does not operate in accordance with the requirements (4.3.2 (a) (i))

Various corrosion around corrosion on vehicle, both underside and top side.

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

nearside front lower brake pipe corrosion

nearside outer and offside outer sill repair heavily coated

offside front inner wing corroded

offside front outrigger/jacking point corroded, strongly advise repair

some under-body corrosion

Bonnet cannot be secured in the closed position (3.1 (b) (i))

Hazard warning switch inoperative (4.4.2 (a) (ii))

Horn not working (7.7 (a) (ii))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))

Nearside Rear Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i))

Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Rear fog lamp not working (4.5.1 (a) (ii))

Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Front Tyre has a tear, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

nearside outer and offside outer sill repair heavily coated

offside front inner wing corroded

offside front outrigger/jacking point corroded, strongly advise repair

some under-body corrosion

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

offside front inner wing corrosion

offside front tyre cracks

some under-body corrosion

Emissions not tested (8.2.1.2 (d))

Exhaust has a major leak of exhaust gases (6.1.2 (a))

Front Brakes imbalanced across an axle Axle 1 (1.2.1 (b) (i))

Horn not working (7.7 (a) (ii))

Nearside Front Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Rear Service brake excessively binding recheck tyre and wheel bearing (1.2.1 (f))

Offside Front Driver's door cannot be opened from outside the vehicle (6.2.3 (a))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Front Position lamp not working (4.2.1 (a))

Offside Rear Service brake excessively binding recheck tyre and wheel bearing (1.2.1 (f))

Offside Rear fog lamp not working (4.5.1 (a) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Service brake efficiency below requirements (1.2.2 (a) (i))

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

front brakes uneven application

offside front inner wing corrosion

some under-body corrosion

Offside Front inner wing by syspesion mts areas

Exhaust system not adequately supported (7.1.1)

Nearside Indicator tell tale inoperative (1.4.A.2a)

Offside Indicator tell tale inoperative (1.4.A.2a)

Offside Rear Rear fog lamp not working (1.3.2b)

Rear Brake load sensing valve linkage defective and function impaired rod to braket washer (3.6.E.3)

Rear Brake load sensing valve linkage defective and function impaired rod to braket washer (3.6.E.3)

Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)

rear brake application uneven pulling to right 60% (3.7.B.2)

Offside Front inner wing by syspesion mts areas

General body corrosion

Front Brakes imbalanced across an axle (3.7.B.5b)

Service brake: efficiency below requirements (3.7.B.7)

General body corrosion

Front Brakes imbalanced across an axle (3.7.B.5b)

Nearside Front Lower Suspension arm ball joint dust cover missing (2.4.G.2)

Nearside Rear Brake load sensing valve seized (3.6.E.3)

Nearside Rear Upper Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Lower Suspension arm ball joint dust cover missing (2.4.G.2)

Offside Rear Rear fog lamp not working (1.3.2b)

Offside Rear Upper Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear rear brake binding (3.7.B.1)

Brakes imbalanced across an axle (3.7.B.5b) DANGEROUS

Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Parking brake mechanism/associated mounting prescribed area is excessively corroded (3.1.9)

Direction indicators flashing less than 60 times a minute (1.4.A.2g)

Driver's seat insecure (6.2.A.1)

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Front passenger seat insecure (6.2.3)

Nearside Front Steering arm has relative movement at its fixings (2.2.B.1h)

Nearside Windscreen washer provides insufficient washer liquid (8.2.3)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Spare wheel insecure (6.4.2)

Battery insecure

Brake pedal creeps down when held under pressure (3.3.B.1a)

Brake pedal spongy (3.3.B.1b)

Brakes imbalanced across an axle (3.7.B.5b)

Front Windscreen washer provides insufficient washer liquid (8.2.3)

Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

front brake application uneven (3.7.B.2)

front brakes release unevenly (3.7.B.4)

rear brake application uneven (3.7.B.2)

rear brakes release unevenly (3.7.B.4)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Inner Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Windscreen washer provides insufficient washer liquid (8.2.3)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear fog lamp missing (1.3.2a)

Offside Windscreen washer provides insufficient washer liquid (8.2.3)