2006 Ford Focus

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Front Brake disc significantly and obviously worn (1.1.14 (a) (i))

Nearside Front Body panel corroded and likely to cause injury wing (6.2.1 (a) (i))

Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength and outer sill has corrosion hole (5.3.6 (a) (i))

Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i))

Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength has corrosion hole (5.3.6 (a) (i))

Registration plate lamp inoperative in the case of a single lamp or all lamps both (4.7.1 (b) (ii))

Nearside Front Tyre has ply or cords exposed (5.2.3 (d) (ii)) DANGEROUS

Offside Front Tyre has ply or cords exposed (5.2.3 (d) (ii)) DANGEROUS

Central heat shield insecure

Front Coil spring corroded both (5.3.1 (b) (i))

Front Direction indicator slightly discoloured both (4.4.3 (a))

Front Subframe mounting prescribed area is corroded but not considered excessive all (5.3.6 (a) (i))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Subframe mounting prescribed area is corroded but not considered excessive all (5.3.6 (a) (i))

Rear Suspension arm corroded but not seriously weakened all (5.3.3 (b) (i))

Service brake fluctuating, but not excessively All (1.2.1 (e))

Sub-frame corroded but not seriously weakened Both (5.3.3 (b) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Sills corroded

Sub-frame corroded but not seriously weakened Both (5.3.3 (b) (i))

Suspension arm corroded but not seriously weakened All (5.3.3 (b) (i))

Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Sills corroded

Sub-frame corroded but not seriously weakened Both (5.3.3 (b) (i))

Suspension arm corroded but not seriously weakened All (5.3.3 (b) (i))

Nearside Front Service brake fluctuating, but not excessively (1.2.1 (e))

Nearside Front Service brake fluctuating, but not excessively (1.2.1 (e))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Nearside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e))

Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Rear Suspension arm corroded but not seriously weakened all (2.4.G.1)

Rear Trailing arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Suspension component mounting prescribed area is corroded but not considered excessive trailing arm mounts (2.4.A.3)

Engine covers fitted obscuring some components in the engine bay

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Under-trays fitted obscuring some underside components

Nail in nearside front tyre

Nail in nearside front tyre

Nearside Rear Direction indicators incorrect colour (1.4.A.2f)

Offside Rear Direction indicators incorrect colour (1.4.A.2f)

Offside Front Suspension arm has slight play in a ball joint (2.4.G.2)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Suspension arm has slight play in a ball joint (2.4.G.2)

Offside Front Suspension arm has slight play in a ball joint (2.4.G.2)

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Front Suspension arm has slight play in a ball joint (2.4.G.2)

Offside Front Suspension arm has slight play in a ball joint (2.4.G.2)

advise n/s rear tyre worn

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)