2010 Volkswagen Caddy

Front Coil spring corroded (5.3.1 (b) (i))

Front Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Nearside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Front Coil spring corroded both (5.3.1 (b) (i))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear reflector defective or damaged by up to 50% of the reflecting surface (4.8.1 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

both rear shock absorbers corroded

Driver's view of the road through the swept area of the windscreen significantly affected by an obstruction (3.1 (a) (ii))

Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Front Obligatory mirror seriously damaged, affecting the rear view (3.3 (b) (ii))

Offside Rear Service brake excessively binding (1.2.1 (f))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Nearside Front Track rod end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) DANGEROUS

Front Coil spring corroded both (5.3.1 (b) (i))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Nearside Rear Service brake binding but not excessively (1.2.1 (f))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear reflector defective or damaged by up to 50% of the reflecting surface (4.8.1 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened both (1.1.14 (a) (ii))

both rear shock absorbers corroded

Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Service brake lagging in operation (1.2.1 (d))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Registration plate lamp does not illuminate simultaneously with the position lamps (4.7.2 (a))

Nearside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e))

Offside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Slight play in rear anti roll bar bushes.

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Brake pad(s) wearing thin (3.5.1g)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Brake pad(s) wearing thin (3.5.1g)

Rear Brake pad(s) wearing thin (3.5.1g)

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Rear Brake pad(s) wearing thin (3.5.1g)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)