MOT Status
ExpiredMileage
111,109 miSignificantly above average — investigate
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))
Exhaust has a major leak of exhaust gases rear (6.1.2 (a))
Nearside Front Body panel corroded and likely to cause injury wing corroded (6.2.1 (a) (i))
Nearside Rear Anti-roll bar linkage corroded and seriously weakened (5.3.3 (b) (i))
Offside Rear Anti-roll bar linkage corroded and seriously weakened (5.3.3 (b) (i))
Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i))
Nearside Front Inner Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Nearside Rear Direction indicator slightly discoloured (4.4.3 (a))
Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Rear Direction indicator slightly discoloured (4.4.3 (a))
Offside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Oil leak, but not excessive (8.4.1 (a) (i))
Rear Exhaust has a minor leak of exhaust gases before backbox (6.1.2 (a))
Oil leak, but not excessive (8.4.1 (a) (i))
Headlamp aim too low (4.1.2 (a))
Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i))
Offside Front Lower Body panel corroded and likely to cause injury wing (6.2.1 (a) (i))
Offside Front Lower Body panel insecure wing (6.2.1 (a) (i))
Offside Front Position lamp not working (4.2.1 (a) (ii))
Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i))
Offside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced wing (6.1.1 (c) (i))
Offside Front Integral body structure is corroded but structural rigidity is not significantly reduced wing (6.1.1 (c) (i))
Offside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Oil leak, but not excessive (8.4.1 (a) (i))
Front Brakes imbalanced across an axle 32% (1.2.1 (b) (i))
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Offside Front Wheel bearing slightly noisy (5.1.3 (b) (i))
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i))
Offside Rear Coil spring fractured or broken (5.3.1 (b) (i))
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Offside Front Wheel bearing slightly noisy (5.1.3 (b) (i))
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Nearside Rear wheel arch starting to corrode
Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Rear wheel arch starting to corrode
Rear Exhaust mounting defective (6.1.2 (a))
Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Front suspension has slight movement at a wishbone pin or bush (2.5.A.1c)
Nearside Rear Shock absorber has slight corrosion to the casing (2.7.2a)
Nearside Rear Suspension arm corroded but not seriously weakened (2.4.G.1)
Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Front suspension has slight movement at a wishbone pin or bush (2.5.A.1c)
Offside Rear Shock absorber has slight corrosion to the casing (2.7.2a)
Offside Rear Suspension arm corroded but not seriously weakened (2.4.G.1)
Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Upper Trailing arm has slight play in a pin/bush (2.4.G.2)
Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Front suspension has slight movement at a wishbone pin or bush (2.5.A.1c)
Nearside Rear Shock absorber has slight corrosion to the casing (2.7.2a)
Nearside Rear Suspension arm corroded but not seriously weakened (2.4.G.1)
Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Front suspension has slight movement at a wishbone pin or bush (2.5.A.1c)
Offside Rear Shock absorber has slight corrosion to the casing (2.7.2a)
Offside Rear Suspension arm corroded but not seriously weakened (2.4.G.1)
Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Upper Trailing arm has slight play in a pin/bush (2.4.G.2)
Nearside Front Tyre worn close to the legal limit (4.1.E.1)
Nearside Rear Front suspension has slight movement at a wishbone pin or bush (2.5.A.1c)
Nearside Rear Shock absorber has slight corrosion to the casing (2.7.2a)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
Offside Rear Front suspension has slight movement at a wishbone pin or bush (2.5.A.1c)
Offside Rear Shock absorber has slight corrosion to the casing (2.7.2a)
Offside Rear Upper Trailing arm has slight play in a pin/bush (2.4.G.2)
Nearside Front Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)
Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Trailing arm has slight play in a pin/bush (2.4.G.2)
Offside Front Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Trailing arm has slight play in a pin/bush (2.4.G.2)
Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Nearside Front Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)
Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Trailing arm has slight play in a pin/bush (2.4.G.2)
Offside Front Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Trailing arm has slight play in a pin/bush (2.4.G.2)
Nearside Rear Tyre worn close to the legal limit (4.1.E.1)
Offside Rear Tyre worn close to the legal limit (4.1.E.1)
Nearside Headlamp aim too low (1.8)
Nearside Rear Tyre worn close to the legal limit (4.1.E.1)
Offside Headlamp aim too high and too far to the right. (1.8)
Offside Rear Tyre worn close to the legal limit (4.1.E.1)
Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Nearside Front Tyre worn close to the legal limit (4.1.E.1)
Front Brake pad(s) wearing thin (3.5.1g)
front brake discs slightly worn
Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Offside Outer Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)
HANDBRAKE LEVER COMING UP HIGH INTERMITTANT
Nearside Front Tyre worn close to the legal limit (4.1.E.1)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
o/s/f tyre outer wall damage
Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)
HANDBRAKE LEVER COMING UP HIGH INTERMITTANT
Nearside Front Tyre worn close to the legal limit (4.1.E.1)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
Offside Rear Tyre worn close to the legal limit (4.1.E.1)
Offside Registration plate lamp not working (1.1.5c)
o/s/f tyre outer wall damage
How Reliable is the Ford Focus?
Based on 28,316,889 MOT tests across 2,072,617 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
CF06 ETZ is a 2006 Ford Focus in Red with a 1,596cc petrol engine. This vehicle has been through 27 MOT tests with a personal pass rate of 59.3%.
Across all 2006 Ford Focus models, the average MOT pass rate is 74.0% with a typical mileage of 75,121 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Ford Focus fails its MOT is tyre tread depth below requirements of 1.6mm, accounting for 1,055,468 recorded failures. If you're considering buying CF06 ETZ, it's worth having these areas checked by a mechanic before committing.
The Ford Focus typically stays on UK roads for around 27 years. At 20 years old, this Ford Focus is well into its expected lifespan but still has years ahead.
Frequently Asked Questions
How do I check the history of CF06 ETZ?
You can check the full history of CF06 ETZ by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was CF06 ETZ registered?
CF06 ETZ is a 2006 Ford Focus, first registered on 22 July 2006.
Is CF06 ETZ safe to buy?
The MOT history for CF06 ETZ shows 27 tests with a 59.3% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does CF06 ETZ have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on CF06 ETZ. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.