2003 Ford Focus

Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Coolant low

Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i))

Windscreen washer not working (3.5 (a))

Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Coolant low

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Offside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner and outer sill (5.3.6 (a) (i))

Offside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))

Heat shield insecure

Front Exhaust has a major leak of exhaust gases flexi pipe (6.1.2 (a))

Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Heat shield insecure

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

exhaust flexi pipe detoriated

exhaust heat shield insecure

Offside Rear Coil spring fractured or broken (5.3.1 (b) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

exhaust flexi pipe detoriated

exhaust heat shield insecure

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill (2.4.A.3)

Offside Rear Seat belt anchorage prescribed area is excessively corroded inner arch to chassis (5.2.6)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Anti-lock braking system warning lamp indicates an ABS fault (3.4.1c)

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Items removed from driver's view prior to test

Nearside Rear coil spring corroded (2.4.C.1b)

Offside Rear coil spring corroded (2.4.C.1b)

Rear and centre exhaust deteriorated

Items removed from driver's view prior to test

Anti-lock braking system warning lamp indicates an ABS fault (3.4.1c)

Items removed from driver's view prior to test

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

Nail in offside rear tyre

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nail in offside rear tyre

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Headlamp aim too low (1.8)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

E.M.L on

Anti-lock braking system warning lamp indicates an ABS fault (3.4.1c)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Nearside Front Headlamp aim too high (1.8)

Offside Front Headlamp aim too high (1.8)

Steering wheel in a condition that hampers proper control (2.1.1)

E.M.L on

Engine management light on

Exhaust has a minor leak of exhaust gases (7.1.2)

Engine management light on

Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Headlamp aim too low and too far to the left. (1.8)

Nearside Rear Tyre has a bulge, caused by separation or partial failure of its structure (4.1.D.1b)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)