2001 Mercedes-benz Vito

Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i))

Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i))

Suspension component mounting prescribed area is corroded but not considered excessive both front inner wing braces (2.4.A.3)

Nearside Front passenger door cannot be opened from inside the vehicle (6.2.B.1b)

Nearside Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a)

Nearside Headlamp aim too high (1.8)

Offside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings crossmember (6.1.B.2)

Suspension component mounting prescribed area is corroded but not considered excessive both front inner wing braces (2.4.A.3)

Rear cross member corroded but not within 30 cms of a load bearing point

Nearside Headlamp aim too low (1.8)

Nearside Outer Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3)

Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3)

Offside Headlamp aim too low (1.8)

Parking brake: efficiency below requirements (3.7.B.7)

Rear cross member corroded but not within 30 cms of a load bearing point

Centre Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive strut top (2.4.A.3)

Rear Body has slight corrosion cross member (6.1.B.2)

Nearside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Nearside Front Track rod end ball joint has excessive play (2.2.B.1f)

Nearside rear parking brake recording little or no effort (3.7.B.6a)

Offside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Centre Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive strut top (2.4.A.3)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Rear Body has slight corrosion cross member (6.1.B.2)

Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Inner Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Front Brake pipe excessively corroded (3.6.B.2c)

Offside Inner Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Track rod end ball joint has excessive play (2.2.B.1f)

Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Nearside Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Nearside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside Stop lamp not working (1.2.1b)

Parking brake: efficiency below requirements (3.7.B.7)

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

n/s inner cv boot

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Stop lamp not working (1.2.1b)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

slight corrosion o/s rear brake disc inner face