2008 Volvo V50

Nearside Rear Inner Tyre worn close to legal limit/worn on edge edge poor (5.2.3 (e))

Offside Rear Inner Tyre worn close to legal limit/worn on edge edge poor (5.2.3 (e))

Oil leak, but not excessive (8.4.1 (a) (i))

Offside Front Inner Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Front Coil spring fractured or broken (5.3.1 (b) (i))

Offside Front Inner Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Offside Rear Upper Position lamp with a multiple light source up to 1/2 not functioning (4.2.1 (a) (i))

Exhaust has a minor leak of exhaust gases pin hole (6.1.2 (a))

Nearside Front Tyre slightly damaged/cracking or perishing sidewall (5.2.3 (d) (ii))

Offside Front Inner Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Oil leak, but not excessive wet but not dripping (8.4.1 (a) (i))

Nearside Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Central Upper Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Headlamp switch does not immediately illuminate all main beam headlamps does not stay on main beam (4.1.3 (a))

Nearside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i))

Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Nearside Rear Inner Tyre has a lump, caused by separation or partial failure of its structure sidewall (5.2.3 (d) (ii)) DANGEROUS

Nearside Rear Inner Tyre has ply or cords exposed edge (5.2.3 (d) (ii)) DANGEROUS

Central Upper Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Headlamp switch does not immediately illuminate all main beam headlamps does not stay on main beam (4.1.3 (a))

Nearside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

brake disc worn, pitted or scored, but not seriously weakened both rear (3.5.1i)

engine covers fitted

o/s/f tyre getting low

o/s/r shock absorber weak

under-trays fitted

engine covers fitted

undersheilds fitted

Windscreen washer provides insufficient washer liquid (8.2.3)

undersheilds fitted

engine covers fitted

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

engine covers fitted

undersheilds fitted

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Windscreen washer provides insufficient washer liquid (8.2.3)

engine covers fitted

undersheilds fitted

Engine covers fitted obscuring some components in the engine bay

Front Brake pad(s) wearing thin (3.5.1g)

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Under-trays fitted obscuring some underside components

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Engine covers fitted obscuring some components in the engine bay

Under-trays fitted obscuring some underside components

centre exhaust corroded

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre has a bulge, caused by separation or partial failure of its structure (4.1.D.1b)

Offside Rear position lamp(s) not working (1.1.A.3b)

Engine covers fitted obscuring some components in the engine bay

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Rear Brake pad(s) wearing thin (3.5.1g)

Under-trays fitted obscuring some underside components

centre exhaust corroded

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Front Tyre(s) incorrect because different size tyres are fitted on the same axle. (4.1.A.1a)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)