2006 Mazda 3

REAR SUSPENSION COMPONENTS CORRODED

SILLS/ BACKING SILLS/ CHASSIS CORRODED

Front Registration plate inscription illegible (0.1 (b))

Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER/ OUTER SILL (5.3.6 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Front Tyre tread depth below requirements of 1.6mm BOTH (5.2.3 (e)) DANGEROUS

Nearside Rear Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

REAR SUSPENSION COMPONENTS CORRODED

SILLS/ BACKING SILLS/ CHASSIS CORRODED

Nearside Front Lower Suspension arm ball joint has slight play (5.3.4 (a) (i))

Nearside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Front Lower Suspension arm ball joint has slight play (5.3.4 (a) (i))

Offside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

plastic cover fitted to sill

Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Shock absorbers has a serious fluid leak (5.3.2 (b))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i))

Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i))

Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i))

Nearside Front Lower Suspension arm ball joint has slight play (5.3.4 (a) (i))

Nearside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Front Lower Suspension arm ball joint has slight play (5.3.4 (a) (i))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

plastic cover fitted to sill

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Suspension component mounting prescribed area is corroded but not considered excessive sills, backing sills (5.3.6 (a) (i))

suspension components/ subframes corroded

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Shock absorbers has a serious fluid leak (5.3.2 (b))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front Suspension arm ball joint has slight play used arm fitted (5.3.4 (a) (i))

sills,backing sills corroded

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Front Windscreen washer provides insufficient washer liquid (3.5 (a))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Rear Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

sills,backing sills corroded

Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i))

Offside Rear Coil spring fractured or broken (5.3.1 (b) (i))

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Front position lamp(s) not working (1.1.A.3b)

Offside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)