2001 BMW 530

Front Exhaust mounting defective bracket broken (6.1.2 (a))

Nearside Front Outer sill holed and corroded

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Outer sill holed and corroded

Offside Front Outer tyre edge wearing close to limit 235/45/r17 97v el

Offside Front fog light in op

Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i))

Offside Rear Rear fog lamp not working (4.5.1 (a) (ii))

Front Exhaust mounting defective bracket broken (6.1.2 (a))

Nearside Front Outer sill holed and corroded

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Outer sill holed and corroded

Offside Front Outer tyre edge wearing close to limit 235/45/r17 97v el

Offside Front fog light in op

Central Exhaust mounting defective bracket (6.1.2 (a))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Brake pipe excessively corroded (1.1.11 (c))

Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Front Lower Suspension arm ball joint excessively worn [rear] (5.3.4 (a) (i))

Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Front Shock absorbers has negligible damping effect (5.3.2 (d))

Central Exhaust mounting defective bracket (6.1.2 (a))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Outer sill jacking point has corrosion

Offside Front Outer sill jacking point has corrosion

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Front jacking point has corrosion

Offside Rear Brake hose slightly deteriorated (1.1.12 (b) (ii))

water pipe porus startint to leak

Nearside Front Brake pipe excessively corroded (1.1.11 (c))

Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Rear Brake hose excessively deteriorated (1.1.12 (b) (ii))

Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i))

Offside Front Brake pipe excessively corroded (1.1.11 (c))

Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Offside Front Service brake excessively binding (1.2.1 (f))

Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i))

Front Brakes imbalanced across an axle by more than 50% (1.2.1 (b) (ii)) DANGEROUS

Offside Rear Brake hose slightly deteriorated (1.1.12 (b) (ii))

corrosion around all jacking points

water pipe porus startint to leak

Nearside Rear Parking brake inoperative on one side (1.4.1 (a))

Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Front Body panel corroded and likely to cause injury Wing arch (6.2.1 (a) (i))

Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Supplementary restraint system warning lamp indicates a fault Air bag (7.1.6 (a))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement D bush (5.3.4 (a) (i))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement D bush (5.3.4 (a) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement Front arm bush (5.3.4 (a) (i))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced Inner sill (6.1.1 (c) (i))

BOTH SIDES FRONT BRAKE PIPES SLIGHTLY CORRODED

VARIOUS SUSPENSION COMPONENTS CORRODED

Vehicle structure has slight corrosion (6.1.A.1)

Nearside Direction indicator incorrect colour (1.4.A.2f)

Fuel system component leaking (7.2.3) DANGEROUS

BOTH SIDES FRONT BRAKE PIPES SLIGHTLY CORRODED

VARIOUS SUSPENSION COMPONENTS CORRODED

Vehicle structure has slight corrosion (6.1.A.1)

Exhaust has a major leak of exhaust gases (7.1.2)

Front brake disc in such a condition that it is seriously weakened (3.5.1i)

Nearside Front Suspension arm has excessive play in a pin/bush (2.4.G.2)

Nearside Registration plate lamp not working (1.1.C.1d)

Offside Rear Upper Tie bar/rod has excessive play in a pin/bush (2.4.G.2)

Parking brake: efficiency below requirements (3.7.B.7)

Trailer electrical socket (13 pin) not operating the trailer lamps as intended (1.9.4)

NOT/GASSED/DUE/TO/EXHAUST

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Anti-lock braking system warning lamp indicates an ABS fault (3.4.1c)

Centre Exhaust system not adequately supported (7.1.1)

Nearside Front Lower Ball joint has excessive play (2.2.B.1f)

Nearside Rear Registration plate lamp not working (1.1.C.1d)

Offside Rear coil spring incomplete (2.4.C.1a)

REAR/HEAT/SHEILDS/ADRIFT

Fuel pipe/s corroded

N/S/R HEAT SHIELD ADRIFT

Nearside Front Brake pipe slightly corroded (3.6.B.2c)

Nearside Front Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Front Brake pipe excessively corroded (3.6.B.2c)

Offside Front Brake pipe excessively corroded (3.6.B.2c)

Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Registration plate lamp not working (1.1.5c)

Front Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)