1986 Mercedes-benz 207 D

Nearside Rear Anti-roll bar attachment bracket/mounting insecure (5.3.3 (a) (i))

Offside Brake master cylinder/servo mounting prescribed area is excessively corroded underside (1.1.21 (e) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Non obligatory mirror damaged

underside of cab corroded

Front Cab or chassis corroded within 30cm of a mounting, but not seriously affecting overall security Both Sides (6.2.2 (d) (i))

Front Suspension component pin or bush slightly worn Kingpin both Sides (5.3.4 (a) (i))

Non obligatory mirror damaged

Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c))

Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Wheel Arch Area (6.1.1 (c) (i))

Rear Exhaust system insecure Tail Pipe (6.1.2 (a))

Driver's seat insecure (6.2.5 (a) (ii)) DANGEROUS

Offside Rear Tyre has ply or cords exposed (5.2.3 (d) (ii)) DANGEROUS

Front Cab or chassis corroded within 30cm of a mounting, but not seriously affecting overall security Both Sides (6.2.2 (d) (i))

Front Suspension component pin or bush slightly worn Kingpin both Sides (5.3.4 (a) (i))

Non obligatory mirror damaged

Trailer electrical socket insecure (4.10 (a) (i))

Nearside Front Cab or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Offside Cab or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Driver footwell has a small hole due to corrosion

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front shock absorbers mounting bolts corroded

Rear Exhaust mounting defective (6.1.2 (a))

Reverse light inop

corrosion N/S/F bulkhead

upper movement in both front kingpins

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Corrosion to N/S/F Bulhead

Drivers footwell has small hole

Front Shock Absorber Bolts Corroded

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Rear Exhaust mounting defective (6.1.2 (a))

Reverse Light inop

Upper movement in kingpins, Both Front

Exhaust mounting defective rear mount poor (6.1.2 (a))

Nearside Front Tyre worn close to legal limit/worn on edge worn on edge (5.2.3 (e))

Nearside Front bulkhead corroded - seen from underneath

Offside Front Tyre slightly damaged/cracking or perishing badly cracked in tread and 2010 tyre (5.2.3 (d) (ii))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

both front shock lower mounting bolts corroded and n/s/f becoming thin

lift in both front king pins

Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Front Hydraulic brake calliper leaking (1.1.16 (b) (i))

Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Exhaust mounting defective rear mount poor (6.1.2 (a))

Nearside Front Tyre worn close to legal limit/worn on edge worn on edge (5.2.3 (e))

Nearside Front bulkhead corroded - seen from underneath

Offside Front Tyre slightly damaged/cracking or perishing badly cracked in tread and 2010 tyre (5.2.3 (d) (ii))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

both front shock lower mounting bolts corroded and n/s/f becoming thin

lift in both front king pins

Cab or chassis corroded within 30cm of a mounting, but not seriously affecting overall security front panel (6.2.2 (d) (i))

Nearside Front bad corrosion around bulk head area

Brake master cylinder/servo mounting prescribed area is excessively corroded body corrosion (see from underside) (1.1.21 (e) (i))

Brake pipe excessively corroded front to rear (1.1.11 (c))

Nearside Front Brake pipe excessively corroded (1.1.11 (c))

Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking point (6.2.2 (d) (i))

Nearside Front Upper Position lamp not working (4.2.1 (a) (ii))

Offside Front Brake pipe excessively corroded (1.1.11 (c))

Offside Front Steering linkage ball joint ball joint dust cover insecure so that it no longer prevents the ingress of dirt both ends split (2.1.3 (g) (ii))

Service brake efficiency below requirements (1.2.2 (a) (i))

Windscreen washer provides insufficient washer liquid both front (3.5 (a))

Cab or chassis corroded within 30cm of a mounting, but not seriously affecting overall security front panel (6.2.2 (d) (i))

Nearside Front bad corrosion around bulk head area

Nearside Front slight play in king pin

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

advise greasing of king pin

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Rear Brake pipe corroded, covered in grease or other material corrosion @ valve (1.1.11 (c))

Front Brake disc significantly and obviously worn (1.1.14 (a) (i))

Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced step area 2.0 (6.1.1 (c) (i))

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Offside Front Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced step area 2.0 (6.1.1 (c) (i))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Rear Brake pipe corroded, covered in grease or other material @ valve (1.1.11 (c))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Obligatory mirror slightly damaged (3.3 (b) (i))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (i))

Nearside Front Lower Hydraulic brake calliper inadequately mounted carrier bolt loose (1.1.16 (c) (i))

Nearside Headlamp aim so that beam "kick up" is not visible on the screen (4.1.2 (a))

Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i))

Offside Headlamp aim too far to the right (4.1.2 (a))

Offside Side repeater not working (4.4.1 (a) (ii))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Spare wheel carrier insecure (6.1.5 (a))

Windscreen washer not working (3.5 (a))

Rear Exhaust fumes causing a danger to health of persons on board exhaust missing (6.1.2 (b) (ii)) DANGEROUS

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Obligatory mirror slightly damaged (3.3 (b) (i))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (i))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Nearside Front Direction indicator not working (1.4.A.2c)

Nearside Front Suspension spring mounting prescribed area is fractured spring front mount (2.4.A.3)

Nearside rear brake recording little or no effort (3.7.B.5a)

Offside Front Suspension spring mounting prescribed area is fractured spring front mount (2.4.A.3)

Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)

Brake master cylinder/servo mounting prescribed area is fractured (3.6.C.3) DANGEROUS

Nearside Front Brake hose bulging under pressure (3.6.B.3) DANGEROUS

Brake hose has slight corrosion to ferrules both front (3.6.B.4e)

Front Drag link end ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)

both step ins corroded. corrosion in front inner wings various locations

o/s/r tyre low on inner edge.

rear body corners damaged

vehicle has had extensive welding repairs to front bulkhead and various chassis repairs

Brake master cylinder/servo mounting prescribed area is excessively corroded 3x places (3.6.C.3)

Nearside Front Lower Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement (2.4.G.2)

Nearside Rear position lamp(s) insecure (1.1.A.3a)

Offside Front Brake hose bulging under pressure (3.6.B.3)

Offside Front Suspension spring mounting prescribed area is excessively corroded crossmember (2.4.A.3)

Offside Rear fog lamp not working (1.3.2b)

Offside rear brake excessively fluctuating (3.7.B.3)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Rear fog lamp tell tale not working (1.3.1b)

Stop lamp not working both (1.2.1b)

Brake hose has slight corrosion to ferrules both front (3.6.B.4e)

Front Drag link end ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)

both step ins corroded. corrosion in front inner wings various locations

o/s/r tyre low on inner edge.

rear body corners damaged

Non obligatory mirror damaged

Nearside Headlamp aim too low (1.8)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Stop lamp not working (1.2.1b)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Non obligatory mirror damaged

o/s/r body insecure

Front Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Front Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Front wheel bearing rough when rotated (2.5.A.2)

Nearside Rear position lamp(s) insecure (1.1.A.3a)

Nearside Windscreen washer provides insufficient washer liquid (8.2.3)

Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded (3.6.C.3)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear fog lamp not working (1.3.2b)

Offside Rear reflector missing (1.5.1a)

Rear Brake hose ferrule excessively corroded (3.6.B.4e)

Rear Brake load sensing valve inoperative (3.6.E.3)

Rear Exhaust has a major leak of exhaust gases (7.1.2)

Rear Towbar component excessively corroded (6.6.1)

Rear fog lamp tell tale not working (1.3.1b)

Nearside Inner Rear Anti-roll bar attachment bracket/mounting insecure (2.4.G.1)

Nearside Obligatory mirror seriously damaged, affecting the rear view (8.1.2a)

park brake cable casing rusty

Brake master cylinder/servo mounting prescribed area is excessively corroded (3.6.C.3)

Nearside Rear Brake pipe inadequately clipped (3.6.B.1)

Offside Inner Rear position lamp(s) not working (1.1.A.3b)

Offside Rear Brake pipe inadequately clipped (3.6.B.1)

park brake cable casing rusty

Nearside Front Axle king pin has slight play in pin and/or bush (2.5.A.3a)

Nearside Front Vehicle structure has slight corrosion (6.1.A.1)

Offside Front Axle king pin has slight play in pin and/or bush (2.5.A.3a)

Offside Front Vehicle structure has slight corrosion (6.1.A.1)

Exhaust has part of the system excessively deteriorated (7.1.1a)

Nearside Rear Registration plate lamp not working (1.1.5c)

Nearside Rear Shock absorber has a serious fluid leak (2.7.3)

Rear Parking brake lever has no reserve travel (3.1.6b)

Nearside Front Axle king pin has slight play in pin and/or bush (2.5.A.3a)

Nearside Front Vehicle structure has slight corrosion (6.1.A.1)

Offside Front Axle king pin has slight play in pin and/or bush (2.5.A.3a)

Offside Front Vehicle structure has slight corrosion (6.1.A.1)

Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Nearside Rear Anti-roll bar has excessive play in a pin/bush (2.4.G.2)

Nearside Rear Registration plate lamp not working (1.1.5c)

Nearside Rear Shock absorber has a serious fluid leak (2.7.3)

Nearside Windscreen wiper blade insecure (8.2.2)

Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.A.1)

Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Windscreen wiper blade insecure (8.2.2)

Parking brake lever has no reserve travel (3.1.6b)

Service brake: efficiency below requirements (3.7.B.7)

Exhaust mounting missing (7.1.1b)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside Rear fog lamp not working (1.3.2b)

Offside rear brake recording little or no effort (3.7.B.5a)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)

Heavy rust scale on rear body supports

Nearside Rear Shock absorber has a light misting of oil (2.7.3)

Steering column top bearing slightly worn (2.1.2c)

Emissions not tested (7.0)

Exhaust has a major leak of exhaust gases (7.1.2)

Exhaust has part of the system excessively deteriorated (7.1.1a)

Nearside Front Brake pipe excessively corroded (3.6.B.2c)

Nearside Headlamp not working on dipped beam (1.7.5a)

Nearside Side repeater not working (1.4.A.2c)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)

Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.A.1)

brake disc excessively pitted (3.5.1h)