2005 Peugeot 206

Nearside Brake pipe corroded, covered in grease or other material Front to rear (1.1.11 (c))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Brake pipe corroded, covered in grease or other material Front to rear (1.1.11 (c))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Wheel bearing has slight play (5.1.3 (a) (i))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b))

Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Nearside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Offside Rear Suspension arm modified so the suspension is inoperative (5.3.3 (c) (ii)) DANGEROUS

Nearside Brake pipe corroded, covered in grease or other material Front to rear (1.1.11 (c))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Brake pipe corroded, covered in grease or other material Front to rear (1.1.11 (c))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Wheel bearing has slight play (5.1.3 (a) (i))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Central Front Exhaust has a major leak of exhaust gases (7.1.2)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Horn not working (1.6.2a)

Nearside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Nearside Front Suspension arm has excessive play in a ball joint (2.4.G.2)

Nearside Front Suspension arm has excessive play in a pin/bush rear (2.4.G.2)

Power steering pipe(s) or hose(s) leaking leaking at rack and pinion (2.3.3b)

Windscreen washer provides insufficient washer liquid both (8.2.3)

Windscreen wiper does not clear the windscreen effectively both (8.2.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Battery insecure (1.9.1)

Nearside Front Suspension arm has excessive play in a ball joint (2.4.G.2)

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Rear Shock absorber has a serious fluid leak (2.7.3)

Offside Headlamp insecure (1.7.3)

Offside Power steering pipe(s) or hose(s) leaking from a seal (2.3.3b)

Offside front brake excessively fluctuating (3.7.B.3)

Registration plate lamp not working both (1.1.C.1d)

Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Headlamp aim too low (1.8)

Rear registration plate deteriorated but not likely to be misread (6.3.1d)

Exhaust emits an excessive level of metered smoke for a non-turbo charged engine (7.4.B.3b)

Nearside Front Shock absorber casing corroded externally so the unit does not function (2.7.2a)

Nearside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Ball joint has excessive play (2.2.B.1f)

Offside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Rear registration plate deteriorated but not likely to be misread (6.3.1d)

Rear registration plate delaminated but not likely to be misread (6.3.1d)

Offside Front Suspension arm has excessive play in a ball joint (2.4.G.2)

Offside Front Track rod end ball joint has excessive play (2.2.B.1f)

Rear registration plate delaminated but not likely to be misread (6.3.1d)

Nearside Rear Exhaust has part of the system slightly deteriorated (7.1.1a)

Horn not working (1.6.2a)

Nearside Headlamp aim too high (1.8)

Offside Headlamp aim too high (1.8)

Nearside front brake binding slightly

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Radiator leaking

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)