1988 Citroen C25

Front Bonnet cannot be secured in the closed position (3.1 (b) (i))

Front Fuel system component leaking Fuel leak from fuel filter (6.1.3 (b) (i))

Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Indicator switch inoperative Indicator stalk not working (4.4.2 (a) (ii))

Main beam tell-tale not working (4.9.1 (a) (ii))

Nearside Front Direction indicator not working (4.4.1 (a) (ii))

Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Front Headlamp insecure (4.1.1 (c))

Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Nearside Rear Service brake excessively binding (1.2.1 (f))

Offside Front Battery insecure and likely to cause a short circuit (4.13 (a) (ii))

Offside Front Direction indicator not working (4.4.1 (a) (ii))

Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Small hole under wheel arch (5.3.6 (a) (i))

Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Rear Brakes imbalanced across an axle by more than 50% 71% (1.2.1 (b) (ii)) DANGEROUS

Front Bonnet skin separating from skin

Front Corrosion around screen

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Front grill and headlamp surround insecure

Nearside Front Headlamp reflector slightly defective (4.1.1 (b) (i))

Nearside Front Wheel bearing has slight play (5.1.3 (a) (i))

Offside Front Headlamp reflector slightly defective (4.1.1 (b) (i))

Offside Front Wheel bearing has slight play (5.1.3 (a) (i))

Rear Rear bumper missing

Battery insecure and likely to cause a short circuit (4.13 (a) (ii))

Main beam tell-tale not working (4.9.1 (a) (ii))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rails (5.3.6 (a) (i))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shocker mount inner wing (5.3.6 (a) (i))

Nearside Front Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i))

Nearside Front Suspension component mounting prescribed area is inadequately repaired shocker mount (5.3.6 (a) (i))

Nearside Headlamp insecure (4.1.1 (c))

Nearside Rear Bumper insecure corner (6.1.4 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength by top shocker mounting in wheel arch (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength front & rear of spring mounts (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength outer & inner sills (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength rear panel (5.3.6 (a) (i))

Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassis rail (7.1.1 (a) (i))

Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i))

Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rails (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i))

Offside Rear Bumper insecure corner (6.1.4 (a) (i))

Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength above anchor mounting (5.3.6 (a) (i))

Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength front & rear of spring mounts (5.3.6 (a) (i))

Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength rear panel (5.3.6 (a) (i))

Nearside Front Wheel bearing has slight play (5.1.3 (a) (i))

Nearside Headlamp reflector slightly defective (4.1.1 (b) (i))

Offside Front Wheel bearing has slight play (5.1.3 (a) (i))

Offside Front panel insecure under headlight

Offside Headlamp reflector slightly defective (4.1.1 (b) (i))

Rear Exhaust has a minor leak of exhaust gases silencer to tail pipe (6.1.2 (a))

bonnet skin separating from frame

Battery insecure and likely to cause a short circuit (4.13 (a) (ii))

Bonnet cannot be secured in the closed position (3.1 (b) (i))

Main beam tell-tale not working (4.9.1 (a) (ii))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Front Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i))

Nearside Headlamp insecure (4.1.1 (c))

Nearside Rear Service brake excessively binding (1.2.1 (f))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i))

Offside Parking brake inoperative on one side (1.4.1 (a))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear cross member holed in many places. (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area . (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength top suspension mounting holed by corrosion. (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength spring mounting, cross member holed by corrosion. (5.3.6 (a) (i))

Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Tie rod mounting. (5.3.6 (a) (ii)) DANGEROUS

Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected top suspension mounting holed by corrosion. (5.3.6 (a) (ii)) DANGEROUS

Head lamp reflectors in poor condition.

inner sills & chassis holed by corrosion in many places.

Floor chassis & inner sills very corroded & in poor condition.

head lamp reflector in poor condition.

Nearside Headlamp not working on dipped beam (1.7.5a)

Offside Headlamp not working on dipped beam (1.7.5a)

Floor chassis & inner sills very corroded & in poor condition.

head lamp reflector in poor condition.

Battery insecure (1.9.1)

Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing/tie bar mounting. (2.4.A.3)

Nearside Rear Suspension spring mounting prescribed area is excessively corroded rear spring hanger mounting area inner & outer (2.4.A.3)

Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg . track control arm mounting. 4 places (2.4.A.3)

Offside Front Suspension component mounting prescribed area is excessively corroded inner wing/tie bar mounting (2.4.A.3)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Rear Suspension spring mounting prescribed area is excessively corroded front spring mount area. (2.4.A.3)

Registration plate lamp not working (1.1.C.1d)

Both head lamp reflectors in poor condition.

chassis & floor pan very corroded in places & in poor condition.

floor & chassis very corroded.

head lamps in poor condition.

Nearside Rear Suspension component mounting prescribed area is excessively corroded upper shock absorber mounting holed (2.4.A.3)

Nearside Seat belt anchorage prescribed area is excessively corroded inner & outer sill holed (5.2.6)

Offside Front Suspension component mounting prescribed area is excessively corroded top suspension mount holed (2.4.A.3)

floor & chassis very corroded.

head lamps in poor condition.

Chassis & floor pan very corroded & in poor condition.

offside head lamp condition .

Nearside Front Brake hose ferrule excessively corroded (3.6.B.4e)

Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Brake hose ferrule excessively corroded (3.6.B.4e) DANGEROUS

Chassis & floor pan very corroded & in poor condition.

offside head lamp condition .

Partsof exhaust system corroded

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Windscreen wipers smearing

Nearside Front constant velocity joint gaiter damaged, but preventing the ingress of dirt (2.5.C.1a)

Corrosion in offside front wheel arch

Headlamps slightly loose

Horn not working (1.6.2a)

Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c)

Corrosion in offside front wheel arch

Headlamps slightly loose

Headlight fixing panels have slight movement.

Vehicle structure has slight corrosion (6.1.A.1)

Nearside Direction indicators adversely affected by the operation of another lamp (1.4.A.2h)

Nearside Front Body has a sharp edge caused by corrosion (6.1.C.1)

Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Nearside Front Headlamp adversely affected by the operation of another lamp (1.7.5c)

Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Front Body has a sharp edge caused by corrosion (6.1.C.1)

Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Rear Body has a sharp edge caused by corrosion (6.1.C.1)

Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Parking brake: efficiency below requirements (3.7.B.7)

Windscreen washer provides insufficient washer liquid (8.2.3)

Brake load sensing valve linkage seized (3.6.E.3)

Nearside Headlamp excessively damaged so that the light output is severely reduced (1.7.5a)

Offside Front Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Registration plate lamp not working (1.1.5c)

Exhaust has a major leak of exhaust gases (7.1.2)

Exhaust tailpipe not capable of allowing the emission probe to be inserted (7.4.B.1)

Nearside Front Front constant velocity joint gaiter split (2.5.C.1a)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Rear Brake load sensing valve linkage seized (3.6.E.3)