MOT Status
ValidMileage
217,930 miSignificantly above average — investigate
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Offside Front Position lamp not working (4.2.1 (a) (ii))
Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Nearside Front Wheel bearing has slight play (5.1.3 (a) (i))
Nearside Front Wheel bearing slightly noisy (5.1.3 (b) (i))
Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Exhaust emissions exceed manufacturer's specified limit (8.2.2.2 (a))
Offside Rear Brake pipe excessively corroded (1.1.11 (c))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Service brake efficiency below requirements (1.2.2 (a) (i))
Nearside Front Coil spring corroded (5.3.1 (b) (i))
Nearside Front Outer sill corroded/holed
Offside Front Coil spring corroded (5.3.1 (b) (i))
Offside Front Inner sill/step corroded
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive strut (5.3.6 (a) (i))
Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
corrosion to chassis
Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b))
Exhaust on a vehicle fitted with a diesel particulate filter emits visible smoke of any colour (8.2.2.2 (d))
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i))
Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Windscreen damaged and affecting the driver's view of the road (3.2 (a) (ii))
Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c))
Front Registration plate deteriorated but not likely to be misread (0.1 (b))
Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Front Tyre has a cut but not deep enough to reach the ply or cords (5.2.3 (d) (i))
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Nearside Integral body structure is corroded but structural rigidity is not significantly reduced Outer sill (6.1.1 (c) (i))
Nearside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))
Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Brake pipe corroded, covered in grease or other material On axle (1.1.11 (c))
Offside Rear Inner Tyre has a cut but not deep enough to reach the ply or cords Multiple (5.2.3 (d) (i))
Offside Rear Outer Tyre has a cut but not deep enough to reach the ply or cords Multiple (5.2.3 (d) (i))
Oil leak, but not excessive (8.4.1 (a) (i))
Nearside Rear Service brake excessively fluctuating (1.2.1 (e))
Front Registration plate deteriorated but not likely to be misread (0.1 (b))
Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Front Tyre has a cut but not deep enough to reach the ply or cords (5.2.3 (d) (i))
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Nearside Integral body structure is corroded but structural rigidity is not significantly reduced Outer sill (6.1.1 (c) (i))
Nearside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))
Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Brake pipe corroded, covered in grease or other material On axle (1.1.11 (c))
Offside Rear Inner Tyre has a cut but not deep enough to reach the ply or cords multiple (5.2.3 (d) (i))
Offside Rear Outer Tyre has a cut but not deep enough to reach the ply or cords multiple (5.2.3 (d) (i))
Oil leak, but not excessive (8.4.1 (a) (i))
Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i))
Front Prop shaft bearing excessively worn (6.1.7 (b) (i))
Headlamp aim not tested (4.1.2 (b))
Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Nearside Rear Inner Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))
Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shock mount (5.3.6 (a) (i))
Offside Front Position lamp not working (4.2.1 (a) (ii))
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch (5.3.6 (a) (i))
Offside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shock mount (5.3.6 (a) (i))
Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength 2nd to rear cross member (5.3.6 (a) (i))
Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) DANGEROUS
Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Front Tyre has a cut but not deep enough to reach the ply or cords (5.2.3 (d) (i))
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Nearside Integral body structure is corroded but structural rigidity is not significantly reduced Outer sill (6.1.1 (c) (i))
Nearside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Rear Outer Tyre has a cut but not deep enough to reach the ply or cords (5.2.3 (d) (i))
Nearside Rear Outer Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))
Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Brake pipe corroded, covered in grease or other material On axle (1.1.11 (c))
Offside Rear Inner Tyre has a cut but not deep enough to reach the ply or cords multiple (5.2.3 (d) (i))
Offside Rear Outer Tyre has a cut but not deep enough to reach the ply or cords multiple (5.2.3 (d) (i))
Oil leak, but not excessive (8.4.1 (a) (i))
Rear Prop shaft bearing has slight play (6.1.7 (b) (i))
Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement dee bush (5.3.4 (a) (i))
Nearside Rear Inner Tyre has a cut but not deep enough to reach the ply or cords (5.2.3 (d) (i))
Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement dee bush (5.3.4 (a) (i))
Oil leak, but not excessive (8.4.1 (a) (i))
Bonnet primary retaining device ineffective (3.1 (c))
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting step area (6.2.2 (d) (i))
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting step area (6.2.2 (d) (i))
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring area (5.3.6 (a) (i))
Offside Rear Position lamp not working (4.2.1 (a) (ii))
Exhaust emits excessive smoke or vapour likely to obscure the vision of other road users (8.2.2.2 (c)) DANGEROUS
Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement dee bush (5.3.4 (a) (i))
Nearside Rear Inner Tyre has a cut but not deep enough to reach the ply or cords (5.2.3 (d) (i))
Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement dee bush (5.3.4 (a) (i))
Oil leak, but not excessive (8.4.1 (a) (i))
advise exhaust outer skin
Nearside Rear Inner Brake prescribed area is excessively corroded chassis leg by l s valve (1.1.21 (e) (i))
Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i))
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i))
Offside Rear Position lamp lens seriously defective broken (4.2.1 (b))
Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member behind rear axle (5.3.6 (a) (i))
Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member in front of rear axle (5.3.6 (a) (i))
advise exhaust outer skin
Nearside Rear Outer Tyre worn close to the legal limit (4.1.E.1)
Offside Rear Outer Tyre worn close to the legal limit (4.1.E.1)
Nearside Front Suspension spring mounting prescribed area is excessively corroded of rear spring (2.4.A.3)
Parking brake mechanism/associated mounting prescribed area is excessively corroded (3.1.9)
Front Brake pad(s) wearing thin (3.5.1g)
Nearside Rear Outer Tyre worn close to the legal limit (4.1.E.1)
Offside Rear Outer Tyre worn close to the legal limit (4.1.E.1)
Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)
Nearside Front Suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)
Nearside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Nearside rear brake application uneven (3.7.B.2)
Offside Front Suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)
Parking brake: efficiency below requirements (3.7.B.7)
Nearside Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Offside Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)
Offside Track rod end ball joint has excessive play (2.2.B.1f)
Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement (2.4.G.2)
Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement (2.4.G.2)
Front Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)
Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
offside & nearside sills corroded outside prescribed areas
Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)
Nearside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)
Offside Front Lower Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)
Offside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)
Nearside rear brake recording little or no effort (3.7.B.5a)
Nearside rear parking brake recording little or no effort (3.7.B.6a)
Offside Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Offside Front Track rod end ball joint has excessive play (2.2.B.1f)
Parking brake: efficiency below requirements (3.7.B.7)
n/s/r back plate damp
Nearside Rear Anti-roll bar insecure (2.4.G.1)
Nearside Rear rear brake recording little or no effort (3.7.B.5a) DANGEROUS
Nearside Rear rear parking brake recording little or no effort (3.7.B.6a) DANGEROUS
Parking brake: efficiency below requirements (3.7.B.7) DANGEROUS
n/s/r back plate damp
Brake pedal anti-slip provision incomplete (3.3.A.1b)
Nearside Front Obligatory mirror does not provide a view to the rear (8.1.2b)
Offside Front Brake hose twisted (found during steering lock to lock check) (2.2.D.2b)
Nearside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Rear Tyre worn close to the legal limit (4.1.E.1)
Nail in offside rear tyre
n/s mirror glass cracked
How Reliable is the Ford Transit?
Based on 16,371,688 MOT tests across 1,454,648 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
F2 NCY is a 2003 Ford Transit in White with a 2,402cc diesel engine. This vehicle has been through 36 MOT tests with a personal pass rate of 58.3%.
Across all 2003 Ford Transit models, the average MOT pass rate is 66.7% with a typical mileage of 108,242 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Ford Transit fails its MOT is registration plate lamp not working, accounting for 551,926 recorded failures. If you're considering buying F2 NCY, it's worth having these areas checked by a mechanic before committing.
The Ford Transit typically stays on UK roads for around 37 years. At 23 years old, this Ford Transit is well into its expected lifespan but still has years ahead.
Frequently Asked Questions
How do I check the history of F2 NCY?
You can check the full history of F2 NCY by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was F2 NCY registered?
F2 NCY is a 2003 Ford Transit, first registered on 21 January 2003.
Is F2 NCY safe to buy?
The MOT history for F2 NCY shows 36 tests with a 58.3% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does F2 NCY have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on F2 NCY. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.