1989 Austin Mini 1000 City E

Central Exhaust has a major leak of exhaust gases front joint slight leak,middle box cracked and slight leak. tail pipe holed. (6.1.2 (a))

Nearside Body component corroded and likely to cause injury door (6.2.1 (a) (i))

Nearside Front Floor excessively deteriorated (6.2.4 (a) (i))

Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced middle sill and rear. (7.1.1 (a) (i))

Nearside Headlamp aim too low (4.1.2 (a))

Nearside Headlamp aim too low and poor pattern. (4.1.2 (a))

Nearside Rear Floor excessively deteriorated (6.2.4 (a) (i))

Nearside Rear Floor excessively deteriorated and sill/sub frame mounting. (6.2.4 (a) (i))

Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Front Floor excessively deteriorated (6.2.4 (a) (i))

Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced middle sill and rear. (7.1.1 (a) (i))

Offside Headlamp aim too far to the right poor pattern. (4.1.2 (a))

Offside Rear Floor excessively deteriorated boot (6.2.4 (a) (i))

Offside Rear Suspension component pin or bush excessively worn radius arm. (5.3.4 (a) (i))

Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected wheel arch. (5.3.6 (a) (ii)) DANGEROUS

Nearside Front Tyre worn close to legal limit/worn on edge worn to 1.8mm. (5.2.3 (e))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear sub-frame slightly corroded.

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Front Brakes imbalanced across an axle Axle 1 (1.2.1 (b) (i))

Nearside Front Upper Suspension component ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Upper Suspension component ball joint excessively worn (5.3.4 (a) (i))

Nearside Rear Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i))

Offside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i))

Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i))

Offside Front Upper Suspension component ball joint excessively worn (5.3.4 (a) (i))

Offside Rear Brake cable damaged (1.1.15 (a))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear fog lamp not working (4.5.1 (a) (ii))

Rear fog lamp tell-tale not working (4.9.1 (a) (ii))

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Brake pedal wearing smooth anti-slip rubber worn (1.1.2 (c))

Engine bay cover obscuring some components

Front Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. slightly uneven application on roller brake test (1.2.1 (b) (i))

Nearside Door panel corroded

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement front bearing (5.3.4 (a) (i))

Nearside Rear Suspension unit damaged but not to excess corroded (5.3.5 (b) (i))

Offside Rear Suspension unit damaged but not to excess corroded (5.3.5 (b) (i))

Oil leak, but not excessive engine (8.4.1 (a) (i))

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. slightly uneven application on roller brake test (1.2.1 (b) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Exhaust emissions - engine idle speed too high (8.2.1.2 (e))

Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b))

Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Brake pedal wearing smooth anti-slip rubber worn (1.1.2 (c))

Engine bay cover obscuring some components

Front Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. slightly uneven application on roller brake test (1.2.1 (b) (i))

Nearside Door panel corroded

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement front bearing (5.3.4 (a) (i))

Nearside Rear Suspension unit damaged but not to excess corroded (5.3.5 (b) (i))

Offside Rear Suspension unit damaged but not to excess corroded (5.3.5 (b) (i))

Oil leak, but not excessive engine (8.4.1 (a) (i))

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. slightly uneven application on roller brake test (1.2.1 (b) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Brake pedal wearing smooth anti-slip rubber worn (1.1.2 (c))

Engine bay cover obscuring some components

Front Brake pad(s) wearing thin approx. 80-85% worn (1.1.13 (a) (ii))

Front Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced around lower screen 'A' pillar (6.1.1 (c) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Oil leak, but not excessive engine (8.4.1 (a) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Exhaust emissions - engine idle speed too high (8.2.1.2 (e))

Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b))

Horn sound not in accordance with requirements (7.7 (c))

Nearside Front Inner Steering linkage ball joint has excessive play track rod ball joint (2.1.3 (b) (i))

Offside Front Inner Steering linkage ball joint has excessive play track rod ball joint (2.1.3 (b) (i))

Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt inner ball joint cover (5.3.4 (b) (ii))

Body corrosion around nearside lower windscreen & doors

Drivers seat fore & aft movement stiff

Engine bay covers obscuring some components

Front Brake pad(s) wearing thin approx. 80-85% worn (1.1.13 (a) (ii))

Nearside Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Subframe mounting repair covered in underseal (5.3.6 (a) (i))

Oil leak, but not excessive engine (8.4.1 (a) (i))

Rear Sub-frame is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Some play in steering rack

Some play in top steering colume bearing

Exhaust emissions carbon monoxide content excessive (7.3.B.1a)

Exhaust emissions hydrocarbon content excessive (7.3.B.1b)

Front Exhaust system not adequately supported bracket broken (7.1.1)

Nearside Front Sub-frame attachment rubber mounting deteriorated resulting in excessive movement front mount (2.4.G.2)

Nearside Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a)

Nearside Rear Suspension component mounting prescribed area is excessively corroded wheel arch (2.4.A.3)

Nearside Seat belt anchorage prescribed area is excessively corroded inner sill panel (5.2.6)

Nearside Track rod end ball joint has excessive play (2.2.B.1f)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Sub-frame attachment rubber mounting deteriorated resulting in excessive movement front mount (2.4.G.2)

Offside Front Sub-frame attachment rubber mounting deteriorated resulting in excessive movement rear mount (2.4.G.2)

Offside Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Rear Subframe mounting prescribed area is excessively corroded wheel arch (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded wheel arch (2.4.A.3)

Offside Rear fog lamp not working (1.3.2b)

Offside Seat belt anchorage prescribed area is excessively corroded inner sill panel (5.2.6)

Offside Seat belt anchorage prescribed area is excessively corroded outer sill panel (5.2.6)

Offside Subframe mounting prescribed area is excessively corroded outer sill panel (2.4.A.3)

Offside rear brake binding (3.7.B.1)

Rear Brakes imbalanced across an axle (3.7.B.5b)

Registration plate lamp not working (1.1.C.1d)

Some play in steering rack

Some play in top steering colume bearing

Front Sub-frame attachment rubber mounting deteriorated resulting in excessive movement both o/s mounts on front subframe (2.4.G.2)

Nearside Rear Suspension component mounting prescribed area is excessively corroded inner arch (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded inner arch 3 seperate holes (2.4.A.3)

Offside Rear fog lamp not working (1.3.2b)

Offside Seat belt anchorage prescribed area is excessively corroded outer sill (5.2.6)

Front Sub-frame attachment rubber mounting deteriorated but not resulting in excessive movement both subframe mounts on n/s (2.4.G.2)

Nearside Play in steering rack inner joint(s) ()

Oil leak ()

Driver's door catch deteriorated but the door can still be readily opened and closed (6.2.B.2)

Exhaust emissions CO high 3.4%

Exhaust emissions HC high 997ppm

Horn grating slightly

Nearside Front Body has slight corrosion floor pan (6.1.B.2)

Nearside Rear Shock absorber has a slightly worn linkage weak damping (2.7.4)

Nearside Rear Tyre worn close to the legal limit worn off on inside edge (4.1.E.1)

Nearside Rear Tyre worn close to the legal limit worn on outside edge (4.1.E.1)

Nearside front 'A' frame corroded around lower windscreen

Offside Front Body has slight corrosion floor pan (6.1.B.2)

Offside Front Tyre worn close to the legal limit worn off on inside edge too 1.6mm (4.1.E.1)

Offside Front suspension has slight play in a upper suspension ball joint (2.5.B.1a)

Offside Rear Shock absorber has a slightly worn linkage weak damping (2.7.4)

Offside Rear Tyre worn close to the legal limit worn on outside edge (4.1.E.1)

Nearside Front Brake pipe slightly corroded by hose (3.6.B.2c)

Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Front Brake pipe slightly corroded by hose (3.6.B.2c)

Offside Inner Front drive shaft coupling flexible rubber or fabric coupling insecure (2.5.C.1e)

Nearside Rear wheel bearing has slight play (2.6.2)

Horn not working (1.6.2a)

Nearside Rear Registration plate lamp not working (1.1.C.1d)

Nearside Lower Suspension arm has excessive play in a pin/bearing (2.4.G.2)

Nearside Rear Rear position lamp(s) incorrect colour (1.1.A.3e)

Nearside Steering rack gaiter split (2.2.D.2d)

Offside Front constant velocity joint gaiter split (2.5.C.1a)

Offside Rear Rear position lamp(s) incorrect colour (1.1.A.3e)

Offside Steering rack gaiter split (2.2.D.2d)

Parking brake: efficiency below requirements (3.7.B.7)

Hazard warning lamps not flashing in phase, with ignition off (1.4.B.1f)

Hazard warning lamps not flashing in phase, with ignition on (1.4.B.1f)

Nearside Front Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Rear Shock absorber has a serious fluid leak (2.7.3)

Nearside Rear wheel bearing has excessive play (2.6.2)

Offside Front Windscreen washer provides insufficient washer liquid (8.2.3)

Offside Rear Rear fog lamp not working (1.3.2b)

Offside Rear Registration plate lamp not working (1.1.5c)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)