2005 Volkswagen Golf

Engine light on

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive sill (5.3.6 (a) (i))

Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))

Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Engine light on

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive sill (5.3.6 (a) (i))

Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))

Engine light on pre requirement of year

Front Suspension arm pin or bush worn but not resulting in excessive movement NS + OS (5.3.4 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brakes imbalanced across an axle (1.2.1 (b) (i))

Seat belt anchorage prescribed area strength or continuity significantly reduced NS sills front + rear as chalked (7.1.1 (a) (i))

Supplementary restraint system warning lamp indicates a fault (7.1.6 (a))

Engine light on / pre requirement's

Front Suspension arm pin or bush worn but not resulting in excessive movement NS+ OS rearmost bush's (5.3.4 (a) (i))

Nearside Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Rear Seat belt anchorage prescribed area is corroded but not considered excessive (7.1.1 (a) (i))

Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Engine light on

Nearside Front Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Front Drive shaft joint constant velocity boot severely deteriorated NS + OS / outers (6.1.7 (g) (i))

Nearside Rear Nail in tyre ()

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Front Service brake binding but not excessively (1.2.1 (f))

Offside Front Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Offside Front Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Nearside Rear position lamp(s) not working (1.1.A.3b)

Offside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc and n/s front outer (2.5.C.1a)

Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Rear Brake pad(s) wearing thin (3.5.1g)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

nearside rear handbrake lever not returning fully on caliper

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)