2008 Ford Ka

Nearside Front Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Brake hydraulic reservoir close to minimum mark (1.1.10 (d) (i))

Central exhaust hanger broken

Front Suspension component mounting prescribed area is corroded but not considered excessive floor both sides (5.3.6 (a) (i))

Nearside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Front Brake damaged, but the braking system is not adversely affected spring missing-ADVISE NEW (1.1.21 (a) (i))

Offside Front Headlamp lens slightly defective condensated (4.1.1 (b) (i))

Offside Rear Outer Suspension component mounting prescribed area is corroded but not considered excessive sill (5.3.6 (a) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive both sides inner sills/chassis (5.3.6 (a) (i))

Nearside Front Headlamp levelling device inoperative (4.1.5 (a))

Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Brake hydraulic reservoir close to minimum mark (1.1.10 (d) (i))

Central exhaust hanger broken

Front Suspension component mounting prescribed area is corroded but not considered excessive floor both sides (5.3.6 (a) (i))

Nearside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Front Brake damaged, but the braking system is not adversely affected spring missing-ADVISE NEW (1.1.21 (a) (i))

Offside Front Headlamp lens slightly defective condensated (4.1.1 (b) (i))

Offside Rear Outer Suspension component mounting prescribed area is corroded but not considered excessive sill (5.3.6 (a) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive both sides inner sills/chassis (5.3.6 (a) (i))

Central exhaust hanger corroded

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Oil leak ()

Central exhaust hanger corroded

Nearside Front Headlamp aim too low (1.8)

Nearside Rear Registration plate lamp not working (1.1.C.1d)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Stop lamp not working (1.2.1b)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Oil leak ()

Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Front Headlamp aim beam image obviously incorrect (1.8.A.1b)

Rear front brake application uneven (3.7.B.2)