2002 Mazda Demio

Brake performance not tested (1.2.1 (g))

Front Position lamp not working BOTH (4.2.1 (a) (ii))

Front Windscreen washer provides insufficient washer liquid (3.5 (a))

Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))

Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Rear Exhaust has a major leak of exhaust gases (6.1.2 (a))

Rear Sub-frame pin or bush excessively worn (5.3.4 (a) (i))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Front Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Front Inner Tyre worn close to legal limit/worn on edge Both (5.2.3 (e))

Nearside Rear Suspension component pin or bush slightly worn Axle (5.3.4 (a) (i))

Offside Rear Suspension component pin or bush slightly worn Rear Axle (5.3.4 (a) (i))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Rear Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Suspension arm pin or bush worn but not resulting in excessive movement Axle beam (5.3.4 (a) (i))

Rear axle beam slightly corroded.

Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Rear Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Suspension arm pin or bush worn but not resulting in excessive movement Axle beam (5.3.4 (a) (i))

Rear axle beam slightly corroded.

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre has a tear, caused by separation or partial failure of its structure perished (4.1.D.1b)

Offside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Rear Suspension component mounting prescribed area is excessively corroded chassis (2.4.A.3)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Front Brake pad(s) wearing thin (3.5.1g)

Offside Rear Nail in tyre ()

n/s/r tyre slight sidewall damage.

Nearside Outer Seat belt anchorage prescribed area is excessively corroded sill (5.2.6)

Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded closing panel (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is excessively corroded axle beam (2.4.A.3)

Offside Rear Inner Suspension component mounting prescribed area is excessively corroded closing panel (2.4.A.3)

Front Brake pad(s) wearing thin (3.5.1g)

Offside Rear Nail in tyre ()

n/s/r tyre slight sidewall damage.

Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Brake hose ferrule excessively corroded (3.6.B.4e)

Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3)

o/s/r tyre perishing and starting to tear

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Rear Tyre has a tear, caused by separation or partial failure of its structure (4.1.D.1b)

o/s/r tyre perishing and starting to tear

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)