2001 Honda Cr-v

Front Driver's view of the road through the swept area of the windscreen materially affected by an obstruction (3.1 (a) (ii))

Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Front Coil spring fractured or broken (5.3.1 (b) (i))

Nearside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Front Upper Suspension arm pin or bush likely to become detached (5.3.4 (a) (ii)) DANGEROUS

Offside Front Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) DANGEROUS

Nearside Front wing mirror damaged

Offside Front Coil spring corroded (5.3.1 (b) (i))

Offside Front Seat belt webbing slightly damaged or frayed (7.1.2 (b) (ii))

Offside Front wing mirror damaged

Rear Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Coil spring corroded (5.3.1 (b) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Rear both side trailing arm bushes

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Coil spring corroded (5.3.1 (b) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Rear both side trailing arm bushes

Windscreen washer provides insufficient washer liquid (3.5 (a))

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Front position lamp(s) not working (1.1.A.3b)

Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Rear Anti-roll bar has slight play in a ball joint (2.4.G.2)

all break pipes are covered with under seal

Front Upper Trailing arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Outer Rear Tyre has a lump, caused by separation or partial failure of its structure (4.1.D.1b)

Offside Front Upper Suspension arm has excessive play in a ball joint (2.4.G.2)

Rear Registration plate lamp not working (1.1.C.1d)

Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Rear Anti-roll bar has slight play in a ball joint (2.4.G.2)

all break pipes are covered with under seal

Child seat fitted not allowing full inspection of adult belt

Exhaust has part of the system slightly deteriorated (7.1.1a)

Exhaust has part of the system slightly deteriorated (7.1.1a)

Fuel pipe/s corroded

Nearside Rear Trailing arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Trailing arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

centre exhaust has been repaired

Offside Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

Rear Exhaust has part of the system slightly deteriorated (7.1.1a)

no oil on dipstick at start of test (topped up)

Radius arm rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)