2003 Subaru Legacy

Boot lid cannot be secured in the closed position (6.2.1 (e))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Exhaust carbon monoxide content after 2nd fast idle exceeds default limits CO 1.66 (8.2.1.2 (b))

Offside Front Outer Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Offside Front Wheel bearing has excessive play (5.1.3 (a) (i))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Brake disc worn, pitted or scored, but not seriously weakened BOTH (1.1.14 (a) (ii))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Front Outer Tyre worn close to legal limit/worn on edge ADVISE REPLACEMENT (5.2.3 (e))

Nearside Rear Nail in tyre ()

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement MAIN AXLE MOUNTING (5.3.4 (a) (i))

Offside Front Inner Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement MAIN AXLE MOUNTING (5.3.4 (a) (i))

All rear suspension components corroded

Exhaust has a minor leak of exhaust gases And all flanges badly corroded (6.1.2 (a))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Macpherson strut corroded but not seriously weakened (5.3.3 (b) (i))

Offside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Rear Brake hose has slight corrosion to ferrule All (1.1.12 (f) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b))

Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b))

Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b))

Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

All rear suspension components corroded

Exhaust has a minor leak of exhaust gases And all flanges badly corroded (6.1.2 (a))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Macpherson strut corroded but not seriously weakened (5.3.3 (b) (i))

Offside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Rear Brake hose has slight corrosion to ferrule All (1.1.12 (f) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Brake hose has slight corrosion to ferrule ALL REARS (1.1.12 (f) (i))

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i))

Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i))

Rear Sub-frame corroded and seriously weakened (5.3.3 (b) (i))

Brake hose has slight corrosion to ferrule ALL REARS (1.1.12 (f) (i))

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Offside Front Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

split pins missing from both track rod end lock nuts

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Brake performance not tested (1.2.1 (g))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b))

Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b))

Offside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) DANGEROUS

Offside Front Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust emissions likely to be affected by an exhaust leak front and rear (8.2.1.1 (b))

Nearside Rear Brake pipe excessively corroded (1.1.11 (c))

Offside Front All position lamps not working (4.2.1 (a))

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Rear Brake pipe excessively corroded (1.1.11 (c))

Offside Stop lamp(s) not working (4.3.1 (a) (ii))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Offside Front Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Anti-lock braking system warning lamp indicates an ABS fault (3.4.1c)

Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2)

Offside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Offside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Front Service brake is causing the steering wheel to severely pull one way binding (3.7.C.2)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

both rear susp bushes starting to spilt

engine light on

exhaust blow

exhaust system starting to corrode

n/s frot bottom wish bone bush starting to spilt

rear chassie legs heavly corrode

rear x/ member rusted

Nearside Front Front wheel bearing has excessive play (2.5.A.3c)

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement anti roll bar (2.4.G.2)

Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement bottom wish boe (2.4.G.2)

both rear susp bushes starting to spilt

engine light on

exhaust blow

exhaust system starting to corrode

n/s frot bottom wish bone bush starting to spilt

rear chassie legs heavly corrode

rear x/ member rusted

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Shock absorber has slight corrosion to the casing (2.7.2a)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

clip missing on nearside headlamp

Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Rear Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Rear Anti-roll bar rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)

Front Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear tyre worn

Offside Front Shock absorber has slight corrosion to the casing (2.7.2a)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)

clip missing n/s headlamp

e.m.l on

Centre Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear coil spring corroded (2.4.C.1b)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear coil spring corroded (2.4.C.1b)

Under-trays fitted obscuring some underside components

eml on.

exhaust heat shield loose

front tyres wearing on edges

Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

Centre Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear coil spring corroded (2.4.C.1b)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear coil spring corroded (2.4.C.1b)

Under-trays fitted obscuring some underside components

eml on.

exhaust heat shield loose

front tyres wearing on edges

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Child seat fitted not allowing full inspection of adult belt

Nearside Headlamp excessively deteriorated so that the light output is severely reduced (1.7.5a)

Offside Front Anti-roll bar linkage insecure (2.4.G.1)

Child seat fitted not allowing full inspection of adult belt

Nearside Front Front suspension has slight deterioration of the bonding between metal and flexible material of an upper support bearing (2.5.B.3a)

Offside Front Front suspension has slight deterioration of the bonding between metal and flexible material of an upper support bearing (2.5.B.3a)

NEAR SIDE FRONT DISC SLIGHTLY GROOVED

Nearside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Offside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2)

Offside Front Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2)

both front brake disc are scored and pitted

Offside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Windscreen washer provides insufficient washer liquid (8.2.3)

Front Brake pad(s) wearing thin (3.5.1g)