1990 Rover Mini

Driver's seat with a defective structure both front seat mounting bolts of incorrect type (6.2.5 (a) (i))

Hazard warning lamps inoperative (4.4.1 (e))

Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch to rear valance corroded through advise attention to all (6.2.2 (d) (i))

Offside Rear Service brake excessively binding (1.2.1 (f))

Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength subframe front mounting to sill/floor section corroded through (5.3.6 (a) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced corrosion on various parts of underbody etc (6.1.1 (c) (i))

Sub-frame corroded but not seriously weakened corrosion on both subframes (5.3.3 (b) (i))

Suspension component ball joint has slight play slight play in various front suspension ball joints also various gaiters deteriorating advise attention (5.3.4 (a) (i))

vehicle undersealed

vehicle underside been welded in several places also on inner wheel aches advise attention

Front Exhaust system insecure (6.1.2 (a))

Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i))

Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting door step (SILL) (6.2.2 (d) (i))

Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor to sill (6.2.2 (d) (i))

Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i))

Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor to sill (6.2.2 (d) (i))

Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking point (6.2.2 (d) (i))

Offside Rear Suspension arm pin or bush excessively worn radius (5.3.4 (a) (i))

Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Valance (6.2.2 (d) (i))

Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Valance (6.2.2 (d) (i))

Offside Rear Outer Suspension arm pin or bush excessively worn Trailing arm mounting pin (5.3.4 (a) (i))

Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Nearside Rear rear brake recording little or no effort (3.7.B.5a)

Nearside Rear rear parking brake recording little or no effort (3.7.B.6a)

Parking brake: efficiency below requirements (3.7.B.7)

Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)

Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill (6.1.B.2)

Offside Inner Front Track rod end ball joint has slight play (2.2.B.1f)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Front Steering rack gaiter split (2.2.D.2d)

Rear fog lamp not working (1.3.2b)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Centre Brake pipe slightly corroded (3.6.B.2c)

Oil leak

fan belt loose and worn

underside of vehicle corroded

Exhaust emissions carbon monoxide content excessive (7.3.B.1a)

fan belt loose and worn

underside of vehicle corroded

engine stabilizer loose

front subframe rear mounts split

rust around master cylinder

Nearside Front wheel bearing has excessive play (2.5.A.3c)

Offside Front constant velocity joint gaiter split (2.5.C.1a)

Offside Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Front wheel bearing has slight play (2.5.A.3c)

engine stabilizer loose

front subframe rear mounts split

rust around master cylinder

Nearside Front Front wheel bearing has slight play (2.5.A.3c)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Front Front wheel bearing has slight play (2.5.A.3c)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Exhaust emissions carbon monoxide content excessive (7.3.B.1a)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Rear fog lamp not working (1.3.2b)

Nearside Front Bonded suspension unit attachment corroded and seriously weakened (2.4.F.1c)

Nearside Front Front constant velocity joint gaiter insecurely mounted to its housing (2.5.C.1a)

Nearside Front Front constant velocity joint gaiter split (2.5.C.1a)

Nearside Front Suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)

Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Nearside Rear Braking system leaking (3.6.A.1)

Nearside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Front Bonded suspension unit attachment corroded and seriously weakened (2.4.F.1c)

Offside Front Suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)