MOT Status
ValidMileage
71,483 miSignificantly above average — investigate
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Front Coil spring corroded (5.3.1 (b) (i))
Fuel Pipe/s corroded
Nearside Front Bumper mountings corroded but not likely to become detached n/s/f damaged but temp repaired and secure (6.1.4 (a) (i))
Nearside Rear Rear reflector defective or damaged by up to 50% of the reflecting surface (4.8.1 (a) (i))
Rear All position lamps have a product on the lenses but not adversely affecting light output rear lenses damaged (4.2.3 (b) (ii))
Rear Service brake requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (c))
Vehicle structure is corroded but structural rigidity is not significantly reduced heavily corroded underbody (6.1.1 (c) (i))
underside covered in alot of underseal
Brake performance unable to be tested Flexi leaking (1.2.1 (g))
Nearside Front Drag link end ball joint has excessive play Marked in chalk (2.1.3 (b) (i))
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill area holed (6.1.1 (c) (i))
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor pan area holed (5.3.6 (a) (i))
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))
Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill area holed (6.1.1 (c) (i))
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor pan area holed (5.3.6 (a) (i))
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))
Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill area holed (6.1.1 (c) (i))
Rear fog lamp not working (4.5.1 (a) (ii))
Offside Front Brake hose leaking on a hydraulic braking system Under arch (1.1.12 (c) (ii)) DANGEROUS
Offside Rear Electrical wiring insulation in such a condition there is an imminent risk of fire or formation of sparks Fog lamp wiring (4.11 (c) (iii)) DANGEROUS
Exhaust mounting defective (6.1.2 (a))
Front Coil spring corroded Both (5.3.1 (b) (i))
Fuel Pipe/s corroded
Nearside Front Lower Bumper damaged
Nearside Rear Rear reflector defective or damaged by up to 50% of the reflecting surface (4.8.1 (a) (i))
Position lamp has a product on the lens or light source but not adversely affecting light intensity Rear lenses damaged (4.2.3 (b) (ii))
Vehicle structure is corroded but structural rigidity is not significantly reduced Heavily corroded underbody (6.1.1 (c) (i))
Brake performance unable to be tested Failure of service brake when attempting brake test (1.2.1 (g))
Emissions unable to be completed Coolant leak and Engine getting hot also aux belt broken (8.2.1.2 (d))
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor area (5.3.6 (a) (i))
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch area (5.3.6 (a) (i))
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor area (5.3.6 (a) (i))
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch area (5.3.6 (a) (i))
Brake pipe connection leaking on a hydraulic braking system Pipe/connection on offside front inner chassis (1.1.11 (b) (ii)) DANGEROUS
Coolant leak Engine area
Nearside Headlamp reflector slightly defective (4.1.1 (b) (i))
Nearside Rear Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis area (5.3.6 (a) (i))
Nearside Rear reflector defective or damaged by up to 50% of the reflecting surface (4.8.1 (a) (i))
Offside Front Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis area (5.3.6 (a) (i))
Offside Headlamp reflector slightly defective (4.1.1 (b) (i))
Battery insecure but not likely to fall from carrier (4.13 (a) (i))
Clutch pedal non slip missing.
Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Front Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis area (5.3.6 (a) (i))
Nearside Headlamp reflector slightly defective (4.1.1 (b) (i))
Nearside Rear Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis area (5.3.6 (a) (i))
Offside Front Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis area (5.3.6 (a) (i))
Offside Headlamp reflector slightly defective (4.1.1 (b) (i))
Nearside Rear Service brake lagging in operation (1.2.1 (d))
Offside Front Position lamp not working (4.2.1 (a) (ii))
Offside Front Service brake excessively binding (1.2.1 (f))
Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))
Battery insecure but not likely to fall from carrier (4.13 (a) (i))
Nearside Headlamp reflector slightly defective (4.1.1 (b) (i))
Nearside Rear Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis area (5.3.6 (a) (i))
Offside Front Direction indicator slightly discoloured (4.4.3 (a))
Offside Front Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis area (5.3.6 (a) (i))
Offside Headlamp reflector slightly defective (4.1.1 (b) (i))
Clutch pedal non slip missing.
Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis area (5.3.6 (a) (i))
Offside Front Direction indicator slightly discoloured (4.4.3 (a))
Offside Front Service brake binding but not excessively (1.2.1 (f))
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive Chassis area (5.3.6 (a) (i))
Reverse lamp inoperative.
Drag link end ball joint has excessive play Bush excessively worn (2.1.3 (b) (i))
Nearside Front Brake pipe excessively corroded (1.1.11 (c))
Nearside Headlamp aim unable to be tested Due to dip beam inoperative (4.1.2 (b))
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch/end of sill area (5.3.6 (a) (i))
Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii))
Offside Rear Service brake lagging in operation (1.2.1 (d))
Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))
Clutch pedal non slip missing.
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis area (5.3.6 (a) (i))
Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Offside Front Direction indicator slightly discoloured (4.4.3 (a))
Offside Front Service brake binding but not excessively (1.2.1 (f))
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive Chassis area (5.3.6 (a) (i))
Reverse lamp inoperative.
Clutch pedal non slip missing.
Front Registration plate deteriorated but not likely to be misread (0.1 (b))
Nearside Headlamp reflector slightly defective (4.1.1 (b) (i))
Nearside Rear Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis/hanger area (5.3.6 (a) (i))
Nearside Rear reflector defective or damaged by up to 50% of the reflecting surface (4.8.1 (a) (i))
Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Offside Front Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))
Offside Headlamp reflector slightly defective (4.1.1 (b) (i))
Rear Brake hose slightly chafed (1.1.12 (b) (i))
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Step/inner sill area (5.3.6 (a) (i))
Clutch pedal non slip missing.
Front Registration plate deteriorated but not likely to be misread (0.1 (b))
Nearside Headlamp reflector slightly defective (4.1.1 (b) (i))
Nearside Rear Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis/hanger area (5.3.6 (a) (i))
Nearside Rear reflector defective or damaged by up to 50% of the reflecting surface (4.8.1 (a) (i))
Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Offside Front Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))
Offside Headlamp reflector slightly defective (4.1.1 (b) (i))
Rear Brake hose slightly chafed (1.1.12 (b) (i))
Brake load sensing valve linkage defective and function impaired (1.1.17 (a))
Nearside Front Direction indicator lens defective such that the emitted light is adversely affected Lens missing (4.4.1 (b) (ii))
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill/step area (5.3.6 (a) (i))
Nearside Front Side repeater lens defective such that the emitted light is adversely affected Lens missing (4.4.1 (b) (ii))
Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis/hanger area (5.3.6 (a) (i))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Cross member (5.3.6 (a) (i))
Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Service brake efficiency below requirements (1.2.2 (a) (i))
Windscreen washer not working (3.5 (a))
Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) DANGEROUS
Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) DANGEROUS
Clutch pedal non slip missing.
Front Registration plate deteriorated but not likely to be misread (0.1 (b))
Nearside Headlamp reflector slightly defective (4.1.1 (b) (i))
Nearside Rear Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis/hanger area (5.3.6 (a) (i))
Nearside Rear Tyre slightly damaged/cracking or perishing Perishing (5.2.3 (d) (ii))
Nearside Rear reflector defective or damaged by up to 50% of the reflecting surface (4.8.1 (a) (i))
Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Offside Front Outer Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))
Offside Headlamp reflector slightly defective (4.1.1 (b) (i))
Rear Brake hose slightly chafed (1.1.12 (b) (i))
Clutch pedal rubber missing
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))
Nearside Rear Tyre slightly damaged/cracking or perishing Perishing (5.2.3 (d) (ii))
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))
Nearside Headlamp aim too high (4.1.2 (a))
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill and end of sill (5.3.6 (a) (i))
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i))
Offside Obligatory mirror insecure (3.3 (b) (ii))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength End of sill (5.3.6 (a) (i))
Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))
Rear Service brake excessively fluctuating (1.2.1 (e))
Windscreen washer not working (3.5 (a))
Offside Rear Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS
Clutch pedal rubber missing
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))
Nearside Rear Tyre slightly damaged/cracking or perishing Perishing (5.2.3 (d) (ii))
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))
Front Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))
Front suspension arms fouling.
Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Track rod end ball joint has slight play (2.1.3 (b) (i))
Offside Rear Tyre worn close to legal limit/worn on edge 2mm tread (5.2.3 (e))
Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))
Rear Suspension component mounting prescribed area is corroded but not considered excessive cross member (5.3.6 (a) (i))
Brake pipe excessively corroded Both pipes from master cylinder (1.1.11 (c))
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))
Exhaust has a major leak of exhaust gases (6.1.2 (a))
Nearside Front Brake pipe excessively corroded (1.1.11 (c))
Nearside Headlamp aim too low (4.1.2 (a))
Nearside Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Nearside Stop lamp(s) not working (4.3.1 (a) (ii))
Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Offside Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Front Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))
Front suspension arms fouling.
Nearside Track rod end ball joint has slight play (2.1.3 (b) (i))
Offside Rear Tyre worn close to legal limit/worn on edge 2mm tread (5.2.3 (e))
Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))
Rear Suspension component mounting prescribed area is corroded but not considered excessive cross member (5.3.6 (a) (i))
Fuel Pipe/s corroded
Headlamp deteriorated but light output not reduced Both (1.7.5a)
Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Tyre worn close to the legal limit (4.1.E.1)
Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. 24% (3.7.B.5b)
Service brake efficiency 53%
coil spring corroded Both front (2.4.C.1b)
Hazard warning switch faulty (1.4.B.1d)
Nearside Front Body has a sharp edge caused by damage Bumper (6.1.C.1)
Nearside Hazard warning lamps inoperative (1.4.B.1b)
Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Offside Headlamp aim too high (1.8)
Rear fog lamp not working (1.3.2b)
Service brake: efficiency below requirements (3.7.B.7)
Fuel Pipe/s corroded
Headlamp deteriorated but light output not reduced Both (1.7.5a)
Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Tyre worn close to the legal limit (4.1.E.1)
coil spring corroded Both front (2.4.C.1b)
slight corrosion to both inner and outer sills but not within any structural components
Front tyres worn on edges
Nearside Rear Direction indicator not working (1.4.A.2c)
Rear Brake pipe excessively corroded both (3.6.B.2c)
Front tyres worn on edges
Brake pipe slightly corroded (3.6.B.2c)
Cut in nearside front tyre.
Nearside Rear reflector slightly damaged but function not impaired (1.5.1c)
Body has a sharp edge caused by damage (6.1.C.1)
Exhaust has a major leak of exhaust gases (7.1.2)
Offside Headlamp aim too high (1.8)
Registration plate lamp not working (1.1.C.1d)
Brake pipe slightly corroded (3.6.B.2c)
Cut in nearside front tyre.
Nearside Rear reflector slightly damaged but function not impaired (1.5.1c)
Service brake: service brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)
Exhaust has a major leak of exhaust gases (7.1.2)
Offside Stop lamp not working (1.2.1b)
Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Stop lamp not working (1.2.1b)
Nearside Front Direction indicators slightly discoloured (1.4.A.2f)
Offside Front Direction indicators slightly discoloured (1.4.A.2f)
n/s/f tyre worn on outer edge
bth ns tyres for tread depth
slight play detected at steering wheel
Loud squeeking from front hubs / brakes in reverse
Nearside Stop lamp not working (1.2.1b)
Offside Stop lamp not working (1.2.1b)
Loud squeeking from front hubs / brakes in reverse
nearside front tyre slightly distorted
How Reliable is the Daihatsu Hijet?
Based on 112,378 MOT tests across 12,157 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
GU52 FYN is a 2002 Daihatsu Hijet in White with a 1,296cc petrol engine. This vehicle has been through 33 MOT tests with a personal pass rate of 57.6%.
Across all 2002 Daihatsu Hijet models, the average MOT pass rate is 66.9% with a typical mileage of 46,253 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Daihatsu Hijet fails its MOT is brake recording little or no effort, accounting for 7,896 recorded failures. If you're considering buying GU52 FYN, it's worth having these areas checked by a mechanic before committing.
The Daihatsu Hijet typically stays on UK roads for around 33 years. At 24 years old, this Daihatsu Hijet is well into its expected lifespan but still has years ahead.
Frequently Asked Questions
How do I check the history of GU52 FYN?
You can check the full history of GU52 FYN by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was GU52 FYN registered?
GU52 FYN is a 2002 Daihatsu Hijet, first registered on 17 October 2002.
Is GU52 FYN safe to buy?
The MOT history for GU52 FYN shows 33 tests with a 57.6% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does GU52 FYN have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on GU52 FYN. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.