2007 Fiat Multipla

Brake disc worn, but not excessively rusty (1.1.14 (a) (i))

Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Nearside Rear Tyre slightly damaged (5.2.3 (d) (ii))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Passenger seat(s) missing at time of test ()

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Suspension component corroded but not seriously weakened (5.3.3 (b) (i))

Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

covers fitted

Battery insecure and likely to cause a short circuit (4.13 (a) (ii))

Exhaust has a major leak of exhaust gases (6.1.2 (a))

Exhaust system insecure (6.1.2 (a))

Front Registration plate inscription illegible (0.1 (b))

Nearside Front Suspension arm pin or bush excessively worn as marked in yellow (5.3.4 (a) (i))

Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i))

Offside Front Suspension arm pin or bush excessively worn as marked in yellow (5.3.4 (a) (i))

Nearside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Offside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Brake disc worn, but not excessively rusty (1.1.14 (a) (i))

Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Nearside Rear Tyre slightly damaged (5.2.3 (d) (ii))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Passenger seat(s) missing at time of test ()

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Suspension component corroded but not seriously weakened (5.3.3 (b) (i))

Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

covers fitted

Brake fluid close to minimum mark (1.1.10 (d) (ii))

Front Inner Brake disc worn, pitted or scored, but not seriously weakened both (1.1.14 (a) (ii))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Front suspension top mountings slightly worn, both sides

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill corroded alongside, and forward of fuel tank (6.2.2 (d) (i))

Brake fluid close to minimum mark (1.1.10 (d) (ii))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Front suspension top mountings slightly worn, both sides

Nearside Rear Tyre worn close to the legal limit inner edge (4.1.E.1)

Offside Rear Tyre worn close to the legal limit inner edge (4.1.E.1)

Front brake disc in such a condition that it is seriously weakened Both (3.5.1i)

Nearside Front Inner Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Rear Rear wheel bearing rough when rotated (2.6.1)

Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill As Marked (6.1.B.2)

Offside Front Inner Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Front brake disc in such a condition that it is seriously weakened Both (3.5.1i)

Nearside Front Inner Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Rear Rear wheel bearing rough when rotated (2.6.1)

Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill As Marked (6.1.B.2)

Offside Front Inner Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside rear brake binding (3.7.B.1)