MOT Status
ExpiredMileage
60,254 miBelow or average mileage for this year
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Bonnet cannot be secured in the closed position (3.1 (b) (i))
Bonnet primary retaining device insecure now missing (3.1 (c))
Brake performance not tested suspension and structure condition (1.2.1 (g))
Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced a pillar (6.1.1 (c) (i))
Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced rear of wheel arch - a pillar/ bulkhead (6.1.1 (c) (i))
Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch / sill end (6.1.1 (c) (i))
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to bulkhead (6.1.1 (c) (i))
Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))
Nearside Front Outer Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i))
Nearside Front Sub-frame attachment bracket/mounting insecure (5.3.3 (a) (i))
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to bulkhead (5.3.6 (a) (i))
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shock top mounting (5.3.6 (a) (i))
Nearside Headlamp aim too low (4.1.2 (a))
Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch / floor - back of arch (6.1.1 (c) (i))
Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch / floor / sill - front of arch (6.1.1 (c) (i))
Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch / sill / floor - front of arch (7.1.1 (a) (i))
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch / floor - back of arch (5.3.6 (a) (i))
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch / sill / floor - front of arch (5.3.6 (a) (i))
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor - quarter seat pocket (7.1.1 (a) (i))
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced quarter panel to floor pan (7.1.1 (a) (i))
Nearside Rear Sub-frame corroded and seriously weakened (5.3.3 (b) (i))
Nearside Rear Sub-frame corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))
Nearside Rear Sub-frame is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i))
Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength boot floor (5.3.6 (a) (i))
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor - quarter seat pocket (5.3.6 (a) (i))
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength quarter panel to floor pan (5.3.6 (a) (i))
Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced a pillar / bulkhead (6.1.1 (c) (i))
Offside Front Inner Suspension component mounting prescribed area is inadequately repaired a pillar base (5.3.6 (a) (i))
Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced a pillar / bulkhead - upper inner wheel arch (6.1.1 (c) (i))
Offside Front Position lamp not working (4.2.1 (a) (ii))
Offside Front Sub-frame attachment bracket/mounting insecure bolt hanging out (5.3.3 (a) (i))
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shock top mounting (5.3.6 (a) (i))
Offside Front Suspension component mounting prescribed area is inadequately repaired bulkhead to floor (5.3.6 (a) (i))
Offside Front Suspension component mounting prescribed area is inadequately repaired floor - incomplete weld (5.3.6 (a) (i))
Offside Headlamp aim too low (4.1.2 (a))
Offside Outer Suspension component mounting prescribed area is inadequately repaired a pillar base - incomplete weld (5.3.6 (a) (i))
Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch / floor - back of arch (6.1.1 (c) (i))
Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch / floor / sill - front of arch (6.1.1 (c) (i))
Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch / sill / floor - front of arch (7.1.1 (a) (i))
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch / floor - back of arch (5.3.6 (a) (i))
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch / sill / floor - front of arch (5.3.6 (a) (i))
Offside Rear Road wheel fixing missing (5.2.1 (a) (i))
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor - quarter seat pocket (7.1.1 (a) (i))
Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength boot floor (5.3.6 (a) (i))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor - quarter seat pocket (5.3.6 (a) (i))
Subframe mounting prescribed area excessively corroded significantly reducing structural strength boot floor / rear panel (5.3.6 (a) (i))
Bonnet seriously at risk of opening inadvertently (3.1 (b) (ii)) DANGEROUS
Nearside Front Tyre has ply or cords exposed (5.2.3 (d) (ii)) DANGEROUS
Nearside Rear Sub-frame fractured (5.3.3 (b) (ii)) DANGEROUS
Nearside Rear Tyre has ply or cords exposed (5.2.3 (d) (ii)) DANGEROUS
Offside Front Tyre has ply or cords exposed (5.2.3 (d) (ii)) DANGEROUS
Offside Rear Tyre has ply or cords exposed (5.2.3 (d) (ii)) DANGEROUS
Stop lamp(s) all not working (4.3.1 (a) (iii)) DANGEROUS
Brake pipe corroded, covered in grease or other material all (1.1.11 (c))
Coolant leak ()
Nearside Front Wheel bearing has slight play (5.1.3 (a) (i))
Nearside Rear Shock absorbers light misting of oil or has limited damping effect weak (5.3.2 (b))
Offside Front Wheel bearing has slight play (5.1.3 (a) (i))
Offside Rear Shock absorbers light misting of oil or has limited damping effect weak (5.3.2 (b))
Offside door frame fractured
Oil leak, but not excessive engine (8.4.1 (a) (i))
Steering system slightly rough (2.1.1 (a))
Suspension component mounting prescribed area is corroded but not considered excessive structure (5.3.6 (a) (i))
petrol cap seal splitting
slight smearing to wipers
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b))
Hazard warning lamps inoperative All (4.4.1 (e))
Horn sound not in accordance with requirements (7.7 (c))
Nearside Headlamp aim too low (4.1.2 (a))
Nearside Headlamp light intensity severely reduced (4.1.4 (a))
Nearside Headlamp not working on main beam (4.1.1 (a) (ii))
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner & outer sill (7.1.1 (a) (i))
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Floor & inner wheel arch (5.3.6 (a) (i))
Offside Headlamp aim too low (4.1.2 (a))
Offside Headlamp light intensity severely reduced (4.1.4 (a))
Offside Headlamp not working on main beam (4.1.1 (a) (ii))
Offside Rear fog lamp lens defective such that emitted light is adversely affected Showing white light (4.5.1 (b) (ii))
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner & outer sill (7.1.1 (a) (i))
Nearside Front Tyre has a tear, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS
Nearside Rear Tyre has a tear, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS
Offside Front Tyre has a tear, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS
Offside Rear Tyre has a tear, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS
Brake pipe corroded, covered in grease or other material Front to rear (1.1.11 (c))
Front Sub-frame pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Oil leak, but not excessive (8.4.1 (a) (i))
All direction indicators flashing less than 60 times a minute (4.4.4 (a))
Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))
Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Battery insecure and likely to cause a short circuit (4.13 (a) (ii))
Emissions not tested vehicle wont idle without choke being on (8.2.1.2 (d))
Front Brakes imbalanced across an axle 36% (1.2.1 (b) (i))
Nearside Front Brake pipe excessively corroded (1.1.11 (c))
Nearside Rear Outer Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))
Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i))
Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i))
Service brake efficiency below requirements (1.2.2 (a) (i))
Windscreen wiper does not clear the windscreen effectively both (3.4 (b) (ii))
All direction indicators flashing less than 60 times a minute (4.4.4 (a))
Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))
Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Offside Front suspension has slight play in a upper suspension ball joint (2.5.B.1a)
Front brake disc in such a condition that it is seriously weakened corroded (3.5.1i)
Hazard warning lamps inoperative (1.4.B.1b)
Nearside Direction indicator flashing less than 60 times a minute (1.4.A.2g)
Nearside Front Outer Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3)
Nearside Headlamp aim too high (1.8)
Nearside Side repeater not working (1.4.A.2c)
Offside Front Brake hose excessively deteriorated (3.6.B.4d)
Offside Front Braking system leaking brake hose (3.6.A.1)
Offside Headlamp aim too high (1.8)
Rear Passenger's seat insecure back (6.2.A.1)
Service brake: efficiency below requirements (3.7.B.7)
Windscreen washer provides insufficient washer liquid (8.2.3)
Offside Front suspension has slight play in a upper suspension ball joint (2.5.B.1a)
Nearside Front Brake pipe slightly corroded (3.6.B.2c)
Nearside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
coolant leak
engine oil leak
Brake pedal anti-slip provision missing (3.3.A.1b)
Exhaust emissions carbon monoxide content excessive (7.3.B.1a)
Exhaust emissions hydrocarbon content excessive (7.3.B.1b)
Exhaust has a major leak of exhaust gases rear box (7.1.2)
Nearside Rear Tyre not fitted in accordance with side wall instructions (4.1.D.1f)
Nearside Stop lamp not working (1.2.1b)
Offside Front Direction indicator incorrect colour (1.4.A.2f)
Offside Front position lamp(s) not working (1.1.A.3b)
Offside Rear Tyre not fitted in accordance with side wall instructions (4.1.D.1f)
Offside Stop lamp not working (1.2.1b)
Nearside Front Brake pipe slightly corroded (3.6.B.2c)
Nearside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
coolant leak
engine oil leak
Nearside Front Brake pipe slightly corroded to hose (3.6.B.2c)
Hazard warning lamps inoperative (1.4.B.1b)
Indicator switch faulty (1.4.A.1)
Nearside Front Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a)
Nearside Front Front suspension has excessive play in a upper suspension ball joint (2.5.B.1a)
Offside Front Front position lamp(s) not working (1.1.A.3b)
Offside Rear fog lamp not working (1.3.2b)
Nearside Front Brake pipe slightly corroded to hose (3.6.B.2c)
Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Nearside Front Brake pipe slightly corroded (3.6.B.2c)
Brakes imbalanced across an axle (3.7.B.5b)
Exhaust emissions carbon monoxide content excessive (7.3.B.1a)
Exhaust emissions hydrocarbon content excessive (7.3.B.1b)
Front Windscreen wiper not operating automatically when switched on (8.2.1b)
Headlamps matched pair are not the same shape (1.7.6)
Offside Front Upper Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)
Offside Front position lamp(s) not working (1.1.A.3b)
Offside Front suspension has excessive play in a upper suspension ball joint (2.5.B.1a)
Offside rear brake recording little or no effort (3.7.B.5a)
Windscreen washer provides insufficient washer liquid (8.2.3)
Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Nearside Front Brake pipe slightly corroded (3.6.B.2c)
Brakes imbalanced across an axle (3.7.B.5b)
Exhaust emissions carbon monoxide content excessive (7.3.B.1a)
Exhaust emissions hydrocarbon content excessive (7.3.B.1b)
Hazard warning lamps inoperative (1.4.B.1b)
Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Nearside rear brake recording little or no effort (3.7.B.5a)
Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Offside Rear Wheel nut(s) missing (4.2.A.1e)
Offside Rear fog lamp missing (1.3.2a)
Rear fog lamp tell tale not working (1.3.1b)
rear brake application uneven (3.7.B.2)
Nearside Lower Front suspension has slight play in an outer ball joint (2.5.B.2a)
Offside Lower Front suspension has slight play in a upper suspension ball joint (2.5.B.1a)
Nearside Rear Tyre worn close to the legal limit (4.1.E.1)
How Reliable is the Rover Mini?
Based on 519,169 MOT tests across 45,631 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
H126 LRX is a 1991 Rover Mini in Black with a 998cc petrol engine. This vehicle has been through 16 MOT tests with a personal pass rate of 50%.
Across all 1991 Rover Mini models, the average MOT pass rate is 64.5% with a typical mileage of 56,005 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Rover Mini fails its MOT is subframe mounting prescribed area is excessively corroded, accounting for 32,036 recorded failures. If you're considering buying H126 LRX, it's worth having these areas checked by a mechanic before committing.
The Rover Mini typically stays on UK roads for around 47 years. At 35 years old, this Rover Mini is well into its expected lifespan but still has years ahead.
Frequently Asked Questions
How do I check the history of H126 LRX?
You can check the full history of H126 LRX by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was H126 LRX registered?
H126 LRX is a 1991 Rover Mini, first registered on 3 May 1991.
Is H126 LRX safe to buy?
The MOT history for H126 LRX shows 16 tests with a 50% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does H126 LRX have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on H126 LRX. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.