2003 Ford Transit

Brake pipe corroded, covered in grease or other material all brake pipes (1.1.11 (c))

Nearside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Suspension component corroded but not seriously weakened (5.3.3 (b) (i))

Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i))

Nearside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i))

Offside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Brake pipe corroded, covered in grease or other material all brake pipes (1.1.11 (c))

Nearside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Suspension component corroded but not seriously weakened (5.3.3 (b) (i))

Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i))

Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))

Nearside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b))

Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))

Offside Rear Leaf spring fractured (5.3.1 (b) (i))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Corrosion in both inner and Outter sills ,none excessive enough to fail

Lower Fluid leak, but not excessive Coolant from radiator (8.4.1 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Some corrosion in both front wings ,does not meet fail critera

Underside of vehicle covered in large amounts of underseal

Horn not working (7.7 (a) (ii))

Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Power steering pump leaking (2.1.5 (a))

Corrosion in both inner and Outter sills ,none excessive enough to fail

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Some corrosion in both front wings ,does not meet fail critera

Underside of vehicle covered in large amounts of underseal

Nearside Front Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting repair covered in underseal (5.3.6 (a) (i))

Offside Rear Suspension spring mounting repair covered in underseal (5.3.6 (a) (i))

Power steering pump has slight seepage (2.1.5 (a))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Strut mount (5.3.6 (a) (i))

Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Front mount (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Shock absorber upper mount (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Rear mount (5.3.6 (a) (i))

Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Front mount (5.3.6 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Front Power steering pump has slight seepage (2.1.5 (a))

Power steering close to minimum mark (2.1.5 (b) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i))

Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing/chassis (5.3.6 (a) (i))

Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i))

Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front sill arch holed corrosion

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

general chassis corrosion

Centre Brake pipe excessively corroded (3.6.B.2c)

Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Brake pipe excessively corroded (3.6.B.2c)

Offside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Offside Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)

Nearside Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Offside Front Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

general body chassis corrosion

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Registration plate lamp not working (1.1.C.1d)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front wheel bearing rough when rotated (2.5.A.2)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Registration plate lamp not working (1.1.C.1d)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

general body chassis corrosion

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

n/s/r tyre cracking on tread

nearside rear tyre cracked & perished

Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front wheel bearing rough when rotated (2.5.A.2)

Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

nearside rear tyre cracked & perished

Offside Front Brake pad(s) wearing thin (3.5.1g)

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

inbalance front brakes

Offside Front Front position lamp(s) not working (1.1.A.3b)

Offside Rear fog lamp not working (1.3.2b)

Offside Stop lamp not working (1.2.1b)

Power steering inoperative (2.3.3a)

Anti-roll bar rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Steering system has slight free play detected at steering wheel (2.2.A.1b)

Nearside Headlamp not working on dipped beam (1.7.5a)

Nearside Windscreen wiper blade insecure (8.2.2)

Offside Coil spring not correctly located (2.4.C.2)

Nail in nearside rear tyre

alternator belt worn

Nearside Registration plate lamp not working (1.1.5c)

Offside Registration plate lamp not working (1.1.5c)

Windscreen has damage to an area in excess of a 10mm circle within zone 'A' (8.3.1a)

Offside Rear Shock absorber has a light misting of oil (2.7.3)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Registration plate lamp not working (1.1.C.1d)

Brakes imbalanced across an axle (3.7.B.5b)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)