2003 Mercedes-benz Vito

Emissions not tested (8.2.2.2 (e))

Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition (8.1.1 (a))

Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Advise rear body panel corroded

Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Brake fluid contaminated (1.8 (a))

Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Rear Tyre has a cut but not deep enough to reach the ply or cords (5.2.3 (d) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords 225/50r17 (5.2.3 (d) (i))

Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Rear Tyre has a cut but not deep enough to reach the ply or cords (5.2.3 (d) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Front Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

advise both rear handbrake cables poor condition

advise front exhaust rubber mounts broken

advise rear brake discs rusty

advise slight noise from offside front top suspension mount bearing

advise: front brake discs rusty

advise: offside corrosion in offside front inner wing

Nearside rear parking brake recording little or no effort (3.7.B.6a)

Parking brake: efficiency below requirements (3.7.B.7)

Nearside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

advise both rear handbrake cables poor condition

advise front exhaust rubber mounts broken

advise rear brake discs rusty

advise slight noise from offside front top suspension mount bearing

advise: front brake discs rusty

advise: offside corrosion in offside front inner wing

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

n/s wiper blade rubber split

under body sills chassis various stages corrosion

Nearside Stop lamp not working (1.2.1b)

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

n/s wiper blade rubber split

under body sills chassis various stages corrosion

Windscreen washer provides insufficient washer liquid (8.2.3)

Brake fluid warning lamp illuminated (3.6.G.2)

Nearside Inner Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Front Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Registration plate lamp not working (1.1.C.1d)

Nearside front brake grabbing slightly (3.7.A.2b)

Offside front brake grabbing slightly (3.7.A.2b)

Nearside front brake grabbing slightly (3.7.A.2b)

Offside front brake grabbing slightly (3.7.A.2b)

Fuel cap/sealing device does not fasten securely by positive means (7.2.4b)

Nearside Front position lamp(s) not working (1.1.A.3b)

Offside Rear wheel bearing rough when rotated (2.6.1)

Offside Stop lamp not working (1.2.1b)

Nearside front brake grabbing slightly (3.7.A.2b)

n/s wiper split

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Registration plate lamp not working (1.1.5c)

Offside Front Suspension arm has excessive play in a pin/bush (2.4.G.2) DANGEROUS

nail in tyre

stone chip in left hand front head lamp not affecting beam pattern