2001 Mercedes-benz Vito

Front Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

both floor to sills slightly corroded

Nearside Front Suspension component mounting prescribed area is excessively corroded Inner flitch (2.4.A.3)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Side repeater incorrect colour Lens Broken (1.4.A.2f)

Nearside Stop lamp not working (1.2.1b)

Nearside Suspension component mounting prescribed area is excessively corroded Inner and outer sill (2.4.A.3)

Nearside rear brake excessively fluctuating (3.7.B.3)

Offside Front Headlamp adversely affected by the operation of another lamp (1.7.5c)

Offside Front Suspension component mounting prescribed area is excessively corroded Inner flitch (2.4.A.3)

Offside Rear fog lamp adversely affected by the operation of another lamp (1.3.2f)

Offside Side repeater incorrect colour Lens Broken (1.4.A.2f)

Offside Stop lamp not working (1.2.1b)

Offside Suspension component mounting prescribed area is excessively corroded Inner and Outer (2.4.A.3)

Parking brake lever has no reserve travel (3.1.6b)

Parking brake: efficiency below requirements (3.7.B.7)

Rear Suspension component mounting prescribed area is excessively corroded Valance/ Crossmember (2.4.A.3)

rear parking brake recording little or no effort Nearside and Offside (3.7.B.6a)

Oil Leaking

Front Lower engine mounting deteriorated, but not resulting in excessive movement (6.1.D.1a)

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Parking brake lever has little reserve travel (3.1.6b)

Play in steering rack inner joint(s)

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Spare tyre defective

Brake load sensing valve seized (3.6.E.3)

Nearside Front Anti-roll bar has excessive play in a ball joint (2.4.G.2)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Anti-roll bar has excessive play in a ball joint (2.4.G.2)

Offside Front coil spring broken (2.4.C.1a)

Offside Track rod end ball joint has excessive play (2.2.B.1f)

Front Lower engine mounting deteriorated, but not resulting in excessive movement (6.1.D.1a)

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Parking brake lever has little reserve travel (3.1.6b)

Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Play in steering rack inner joint(s)

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Spare tyre defective

Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Front Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)

Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Front Side repeater incorrect colour (1.4.A.2f)

Offside Rear position lamp(s) not working (1.1.A.3b)

Rear Brake pipe excessively corroded (3.6.B.2c)

Horn not working (1.6.2a)

Nearside Front Tyre has a lump, caused by separation or partial failure of its structure (4.1.D.1b)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Anti-roll bar has excessive play in a ball joint (2.4.G.2)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Headlamp aim too high (1.8)

Nearside Front Anti-roll bar has slight play in a ball joint (2.4.G.2)

Nearside Side repeater slightly discoloured (1.4.A.2f)

Offside Front Suspension arm has slight play in a pin/bush (2.4.G.2)

Offside Side repeater slightly discoloured (1.4.A.2f)

Nearside Front Brake pipe excessively corroded (3.6.B.2c)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

front exhaust rubber mounting missing