2003 Mercedes-benz Vito

Nearside Front Road wheel slightly distorted (5.2.2 (c) (i))

Nearside Registration plate lamp dim

Offside Rear Road wheel slightly distorted (5.2.2 (c) (i))

Trailer electrical socket insecure (4.10 (a) (i))

Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i))

Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Nearside Front Tyre has a tear, caused by separation or partial failure of its structure 225/40/18 (5.2.3 (d) (ii)) DANGEROUS

Offside Front Tyre has a tear, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Both inner sills corroded

Both outer sills corroded

Front Service brake fluctuating, but not excessively (1.2.1 (e))

Nearside Front Road wheel slightly distorted (5.2.2 (c) (i))

Nearside Registration plate lamp dim

Offside Front Outer Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Offside Rear Road wheel slightly distorted (5.2.2 (c) (i))

Rear Service brake fluctuating, but not excessively (1.2.1 (e))

Trailer electrical socket insecure (4.10 (a) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))

vehicle heavily under sealed

Horn not working (7.7 (a))

Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i))

Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i))

Nearside Rear Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced Sill not fully welded (6.1.1 (d) (i))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))

vehicle heavily under sealed

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Excessive corrosion outside or prescribed areas, various areas of filler in sills and underside heavily undersealed over corrosion

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill and wheelarch (5.3.6 (a) (i))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i))

Offside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Excessive corrosion outside or prescribed areas, various areas of filler in sills and underside heavily undersealed over corrosion

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Vehicle heavily undersealed

Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Rear Coil spring fractured or broken (5.3.1 (b) (i))

Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Windscreen wiper blade defective (3.4 (b) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Windscreen wiper blade defective (3.4 (b) (i))

Vehicle heavily undersealed

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Seat belt anchorage prescribed area is corroded but not considered excessive (7.1.1 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Seat belt anchorage prescribed area is corroded but not considered excessive (7.1.1 (a) (i))

Exhaust mounting defective (6.1.2 (a))

Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill/arch - as chalked (5.3.6 (a) (i))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Exhaust mounting defective (6.1.2 (a))

Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Exhaust mounting defective (6.1.2 (a))

Filler in sills

Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside front outer constant velocity joint gaiter leaking grease around clip

Towbar slightly corroded within 30cm of towbar mounting (6.1.6 (i) (i))

Vehicle heavily undersealed

Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Side repeater incorrect colour (4.4.3 (a))

Offside Rear Rear fog lamp not working (4.5.1 (a) (ii))

Exhaust mounting defective (6.1.2 (a))

Filler in sills

Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside front outer constant velocity joint gaiter leaking grease around clip

Towbar slightly corroded within 30cm of towbar mounting (6.1.6 (i) (i))

Vehicle heavily undersealed

Front Wheel/tyre protruding beyond wheel arch and rears ()

Horn not working properly weak (7.7 (a) (i))

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened and offside (1.1.14 (a) (ii))

Nearside Rear Brake hose slightly deteriorated and offside (1.1.12 (b) (ii))

Offside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Play in steering rack inner joint(s) ()

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

chassis coated in thick wax oil restricting view in some areas

Front Wheel/tyre protruding beyond wheel arch and rears ()

Hazard warning lamps inoperative (4.4.1 (e))

Horn not working properly weak (7.7 (a) (i))

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened and offside (1.1.14 (a) (ii))

Nearside Rear Brake hose slightly deteriorated and offside (1.1.12 (b) (ii))

Offside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Play in steering rack inner joint(s) ()

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

chassis coated in thick wax oil restricting view in some areas

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Brake disc worn, pitted or scored, but not seriously weakened n/s and o/s (1.1.14 (a) (ii))

Rear brake hose ferrules coated in grease

chassis and components coated in anti corrosion spray

Hazard warning switch inoperative has no lights ign on or off (4.4.2 (a) (ii))

Horn not working (7.7 (a) (ii))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill within 30 cm of suspension mounting (5.3.6 (a) (i))

Offside Front Lower Suspension arm ball joint excessively worn outer (5.3.4 (a) (i))

Nearside Rear Tyre has a bulge, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Offside Rear Tyre has a lump, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Offside Front Steering system lightly rubbing wheel arch liner loose needs securing (2.1.4 (a))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Power steering component has slight seepage from a component filler tank damp poss spillage (2.1.5 (a))

Rear Brake disc worn, pitted or scored, but not seriously weakened n/s and o/s (1.1.14 (a) (ii))

Rear Brake hose has slight corrosion to ferrule n/s and o/s (1.1.12 (f) (i))

n/s sill corroded in centre

rear valance n/s and o/s corroded advise welding

Nearside Rear Body has slight corrosion (6.1.B.2)

Offside Front Upper Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Front Electronic stability system warning lamp indicates a fault (3.4.1c)

Front Lower Exhaust system not adequately supported (7.1.1)

Front Parking brake lever has no reserve travel (3.1.6b)

Nearside Front Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Nearside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Nearside Rear coil spring broken (2.4.C.1a)

Offside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Rear Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Parking brake: efficiency below requirements (3.7.B.7)

Nearside Rear Body has slight corrosion (6.1.B.2)

Parking brake lever has little reserve travel (3.1.6b)

Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Rear Service brake: service brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Nearside Inner Front constant velocity joint gaiter damaged, but preventing the ingress of dirt (2.5.C.1a)

Offside Inner Front constant velocity joint gaiter damaged, but preventing the ingress of dirt (2.5.C.1a)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Hazard warning switch faulty (1.4.B.1d)

both front side lights dull

Nearside Inner Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Windscreen has damage to an area in excess of a 10mm circle within zone 'A' (8.3.1a)

Nearside Inner Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Front Brake pad(s) wearing thin (3.5.1g)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Front Brake pad(s) wearing thin (3.5.1g)

Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Front Brake hose excessively deteriorated (3.6.B.4d)

Front position lamp(s) not working (1.1.A.3b)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Registration plate lamp not working (1.1.5c)

Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)