MOT Status
ExpiredMileage
307,610 miSignificantly above average — investigate
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Front chassis to cab corr/holed
Offside Rear Inner Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Oil leak, but not excessive (8.4.1 (a) (i))
Nearside Front Tyre worn close to legal limit/worn on edge worn smooth on outer edge (5.2.3 (e))
Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Oil leak, but not excessive (8.4.1 (a) (i))
Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Nearside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i))
Nearside Side repeater not working (4.4.1 (a) (ii))
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Offside Stop lamp(s) not working (4.3.1 (a) (ii))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))
Windscreen washer provides insufficient washer liquid (3.5 (a))
Nearside Registration plate lamp throwing direct white light to the rear (4.7.1 (a))
Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Central Seat belt not functioning as intended (7.1.2 (c))
Front Registration plate missing (0.1 (a))
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Front Brake hose slightly deteriorated both front hoses (1.1.12 (b) (ii))
Front Suspension arm pin or bush worn but not resulting in excessive movement all front bushes (5.3.4 (a) (i))
Nearside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))
Rear Vehicle structure is corroded but structural rigidity is not significantly reduced rear chassis corrotion (6.1.1 (c) (i))
Front Headlamp not working on dipped beam both no working (4.1.1 (a) (ii))
Nearside Front Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting inner wing holed (6.2.2 (d) (i))
Windscreen washer not working (3.5 (a))
Nearside Floor in such a condition it is likely to cause injury cab floor rusted & holed (6.2.4 (a) (ii)) DANGEROUS
Offside Rear Outer Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS
Front Brake hose slightly deteriorated both front hoses (1.1.12 (b) (ii))
Front Suspension arm pin or bush worn but not resulting in excessive movement all front bushes (5.3.4 (a) (i))
Nearside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))
Rear Vehicle structure is corroded but structural rigidity is not significantly reduced rear chassis corrotion (6.1.1 (c) (i))
Nearside Front Inner Cab or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))
Front Headlamp aim so that beam "kick up" is not visible on the screen nearside & offside (4.1.2 (a))
Front Side repeater not working both wing indicators not working (4.4.1 (a) (ii))
Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))
Nearside Rear Lower Suspension component pin or bush excessively worn (5.3.4 (a) (i))
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii))
Offside Front Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i))
Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i))
Rear Anti-roll bar pin or bush excessively worn Rear roll bushes worn (5.3.4 (a) (i))
Rear Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i))
Offside Rear Inner Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS
Nearside Front Inner Cab or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))
Offside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Offside Front inner door handle insecure, door still opens
Offside Front inner wing holed by corrosion
Offside Rear Tyre worn close to the legal limit outer, 2mm (4.1.E.1)
Offside Rear axle bump stop not fitted
Nearside Front Seat belt locking mechanism does not secure or release (5.2.5a)
Nearside Front Side repeater not working (1.4.A.2c)
Nearside Front position lamp(s) not working (1.1.A.3b)
Nearside Rear Body has excessive displacement which may lead to loss of vehicle control mount bolt loose (6.1.B.1a)
Nearside Rear Brake cable has wires broken and is significantly weakened hand brake (3.5.1b)
Nearside Registration plate lamp not working (1.1.C.1d)
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded (3.6.C.3)
Offside Rear Body has excessive displacement which may lead to loss of vehicle control body mounting cracked and displaced (6.1.B.1a)
Offside Registration plate lamp not working (1.1.C.1d)
Offside Front inner door handle insecure, door still opens
Offside Front inner wing holed by corrosion
Offside Rear Tyre worn close to the legal limit outer, 2mm (4.1.E.1)
Offside Rear axle bump stop not fitted
Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Nearside Front suspension has slight play in a upper suspension ball joint (2.5.B.1a)
n/s and o/s rear body bolts loose
Brake fluid warning lamp illuminated (3.6.G.2)
Nearside Rear Inner Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Windscreen washer provides insufficient washer liquid (8.2.3)
Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Nearside Front suspension has slight play in a upper suspension ball joint (2.5.B.1a)
n/s and o/s rear body bolts loose
Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b)
Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Nearside Front Brake pipe slightly corroded (3.6.B.2c)
Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)
Exhaust has a major leak of exhaust gases (7.1.2)
Nearside Rear Rear position lamp(s) not working (1.1.A.3b)
Offside Front Body has a sharp edge caused by damage (6.1.C.1)
Offside Upper Front position lamp(s) not working (1.1.A.3b)
Nearside Front Brake pipe slightly corroded (3.6.B.2c)
Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)
coolant leaking
engine oily
n/s/f tyre bold on outter edge
n/s/f tyre getting low
n/s/r outter tyre perished
o/s/r tyres getting close to llegal limit of 1.6mm
Nearside Front Headlamp aim beam image obviously incorrect (1.8.A.1b)
Offside Front Headlamp aim beam image obviously incorrect (1.8.A.1b)
Offside Front Seat belt damaged sufficient to significantly weakened the webbing (5.2.2a)
Offside Rear position lamp(s) not working (1.1.A.3b)
coolant leaking
engine oily
n/s/f tyre bold on outter edge
n/s/f tyre getting low
n/s/r outter tyre perished
o/s/r tyres getting close to llegal limit of 1.6mm
Brake warning light on (offside front pad sensor wire broken)
Cab mounts split
Exhaust has a minor leak of exhaust gases (7.1.2)
Immobiliser warning light intermittantly flashing
Nearside rear wheel bearing leaking (oil not on brakes)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside wide angled mirror glass missing
Oil leak
Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)
Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)
Brake load sensing valve seized (3.6.E.3)
Nearside Headlamp aim too low (1.8)
Nearside Rear Body insecure and dangerous to other road users (6.1.B.1b)
Nearside Rear Brake pipe excessively corroded (3.6.B.2c)
Nearside Rear position lamp(s) not working (1.1.A.3b)
Nearside Registration plate lamp not working (1.1.C.1d)
Offside Front Brake hose excessively chafed (3.6.B.4d)
Offside Front Brake hose twisted (found during steering lock to lock check) (2.2.D.2b)
Offside Front position lamp(s) not working (1.1.A.3b)
Offside Headlamp aim too low (1.8)
Offside Rear Body insecure and dangerous to other road users (6.1.B.1b)
Offside Rear rear parking brake recording little or no effort (3.7.B.6a)
Offside Registration plate lamp not working (1.1.C.1d)
Parking brake: efficiency below requirements (3.7.B.7)
All side marker lamps not working
Bonnet release handle broken
Brake warning light on (offside front pad sensor wire broken)
Cab mounts split
Exhaust has a minor leak of exhaust gases (7.1.2)
Immobiliser warning light intermittantly flashing
Nearside rear bump stop missing
Nearside rear wheel bearing leaking (oil not on brakes)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside wide angled mirror glass missing
Oil leak
Gearbox mounting broken
Oil leak
rear body bolts loose
Nearside Front Upper Front position lamp(s) not working (1.1.A.3b)
Nearside Fuel pipe leaking (7.2.3)
Nearside Headlamp aim beam image kick up to the offside (1.8)
Nearside Outer Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)
Nearside rear parking brake recording little or no effort (3.7.B.6a)
Offside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Parking brake: efficiency below requirements (3.7.B.7)
Oil leak
Parking brake lever has little reserve travel (3.1.6b)
rear body bolts loose
Rear Body has slight displacement of the body relative to the chassis (6.1.B.1a)
Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)
Nearside Rear Brake pipe excessively corroded (3.6.B.2c)
Offside Front Brake pipe excessively corroded (3.6.B.2c)
Offside Rear Brake pipe excessively corroded (3.6.B.2c)
Rear Brake load sensing valve has been disconnected and was fitted as standard (3.6.E.2)
Rear Brake load sensing valve linkage seized (3.6.E.3)
Spare wheel insecure (6.4.2)
Rear Body has slight displacement of the body relative to the chassis (6.1.B.1a)
Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)
Nearside Front Brake pipe slightly corroded (3.6.B.2c)
Nearside Inner Rear Tyre worn close to the legal limit (4.1.E.1)
Nearside Rear Brake pipe slightly corroded (3.6.B.2c)
Nearside Rear Leaf spring splayed and lightly rubbing (2.4.B.1c)
Offside Rear Brake pipe slightly corroded (3.6.B.2c)
Offside Rear Leaf spring splayed and lightly rubbing (2.4.B.1c)
Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)
Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)
n/s/r sideboard light lens missing showing white light
o/s/r sideboard light inop.
Spare tyre defective
Brakes imbalanced across an axle (3.7.B.5b)
Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Nearside Front brake disc slightly pitted (3.5.1h)
Offside Front brake disc slightly pitted (3.5.1h)
Spare tyre defective
How Reliable is the Iveco Dailey?
Based on 3,131 MOT tests across 240 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
HY51 BSZ is a 2002 Iveco Dailey in White with a 2,800cc diesel engine. This vehicle has been through 29 MOT tests with a personal pass rate of 55.2%.
Across all 2002 Iveco Dailey models, the average MOT pass rate is 62.2% with a typical mileage of 119,703 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Iveco Dailey fails its MOT is parking brake: efficiency below requirements, accounting for 367 recorded failures. If you're considering buying HY51 BSZ, it's worth having these areas checked by a mechanic before committing.
The Iveco Dailey typically stays on UK roads for around 30 years. At 24 years old, this Iveco Dailey is approaching the upper end of the typical lifespan for this model.
Frequently Asked Questions
How do I check the history of HY51 BSZ?
You can check the full history of HY51 BSZ by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was HY51 BSZ registered?
HY51 BSZ is a 2002 Iveco Dailey, first registered on 2 January 2002.
Is HY51 BSZ safe to buy?
The MOT history for HY51 BSZ shows 29 tests with a 55.2% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does HY51 BSZ have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on HY51 BSZ. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.