1992 Citroen C15

Offside Front Service brake excessively binding (1.2.1 (f))

Offside Rear Service brake excessively binding (1.2.1 (f))

Offside Rear fog lamp not working (4.5.1 (a) (ii))

Nearside Front Inner Seat belt anchorage prescribed area is corroded but not considered excessive door step (7.1.1 (a) (i))

Nearside Front Steering rack has slight free play detected at steering wheel (2.3 (a) (i))

Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Front Outer Seat belt anchorage prescribed area is corroded but not considered excessive sill (7.1.1 (a) (i))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Front Inner Seat belt anchorage prescribed area is corroded but not considered excessive door step (7.1.1 (a) (i))

Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Front Outer Suspension component mounting prescribed area is corroded but not considered excessive sill (5.3.6 (a) (i))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Side repeater not working (4.4.1 (a) (ii))

Offside Headlamp aim too high (4.1.2 (a))

Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength 2 places (5.3.6 (a) (i))

Rear Exhaust system insecure (6.1.2 (a))

Rear fog lamp not working (4.5.1 (a) (ii))

Windscreen washer not working (3.5 (a))

Nearside Front Inner Seat belt anchorage prescribed area is corroded but not considered excessive door step (7.1.1 (a) (i))

Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Front Outer Suspension component mounting prescribed area is corroded but not considered excessive sill (5.3.6 (a) (i))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive floor (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive by cross member (5.3.6 (a) (i))

Nearside Rear hand brake needs ajusting

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive cross member (5.3.6 (a) (i))

Driver's view of an obligatory external mirror significantly affected by an obstruction (3.1 (a) (ii))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i))

Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive floor (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive by cross member (5.3.6 (a) (i))

Nearside Rear hand brake needs ajusting

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive cross member (5.3.6 (a) (i))

Windscreen wiper blade defective (3.4 (b) (i))

Nearside Rear cross member corroded

Offside Rear cross member corroded

lower engine mounting worn

Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut surport (5.3.6 (a) (i))

Nearside Headlamp aim too high (4.1.2 (a))

Offside Headlamp aim too high (4.1.2 (a))

Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Lower engine mounting has slight play

Nearside Rear cross member corroded

Offside Rear cross member corroded

Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut surport (5.3.6 (a) (i))

Nearside Headlamp aim too high (4.1.2 (a))

Offside Headlamp aim too high (4.1.2 (a))

Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Lower engine mounting has slight play

Nearside Rear cross member corroded

Offside Rear cross member corroded

Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Rear Inner Suspension component corroded but not seriously weakened valance (5.3.3 (b) (i))

Brake load sensing valve inoperative but ABS functioning (1.1.17 (c) (i))

Driver's view of an obligatory external mirror significantly affected by an obstruction (3.1 (a) (ii))

Exhaust has a major leak of exhaust gases (6.1.2 (a))

Nearside Headlamp aim not tested (4.1.2 (b))

Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Headlamp aim too high (4.1.2 (a))

Rear Exhaust system insecure (6.1.2 (a))

Registration plate lamp does not illuminate simultaneously with the position lamps (4.7.2 (a))

Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a))

Nearside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Hazard warning switch inoperative (4.4.2 (a) (ii))

Nearside Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i))

Offside Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Brake load sensing valve inoperative and ABS not fitted or inoperative (1.1.17 (c) (ii)) DANGEROUS

Central Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front sub frame corroded

Offside Front Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

body corroded

Hazard warning switch inoperative (4.4.2 (a) (ii))

Nearside Front Brake disc significantly and obviously worn inner side (1.1.14 (a) (i))

Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wing (6.2.2 (d) (i))

Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting lower inner side wing area (6.2.2 (d) (i))

Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i))

Nearside Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill in various areas (6.2.2 (d) (i))

Nearside Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill in various areas (6.2.2 (d) (i))

Offside Front Brake disc significantly and obviously worn inner side (1.1.14 (a) (i))

Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill in various areas (6.2.2 (d) (i))

Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wing under bonnet area (6.2.2 (d) (i))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Rear Rear fog lamp not working (4.5.1 (a) (ii))

Rear fog lamp switch inoperative (4.5.3 (a) (ii))

Front Exhaust has a minor leak of exhaust gases pipe (6.1.2 (a))

both front inner brake pads starting to wear,ok at test.

Nearside Rear Tyre fouling a part of the vehicle (4.1.D.2)

Offside Rear Tyre fouling a part of the vehicle (4.1.D.2)

fan belt needs adjustment

nearside and offside rear radius arm bearings deteriorating

nearside and offside rear tyres perished

Centre Rear Brake lever has restricted free movement load valve seized (3.5.1k)

Offside Front Side repeater not working (1.4.A.2c)

Offside Front Subframe mounting prescribed area is excessively corroded chassis / floorpan (2.4.A.3)

Offside Front Suspension spring mounting prescribed area is excessively corroded upper inner top strut mount (2.4.A.3)

fan belt needs adjustment

nearside and offside rear radius arm bearings deteriorating

nearside and offside rear tyres perished

nearside front rolbar bush worn

offside front rollbar bush worn

rear radius arm bearings starting to deteriorate nearside

rear radius arm bearings starting to detreriorate offside

Exhaust has a major leak of exhaust gases (7.1.2)

Hazard warning lamps inoperative (1.4.B.1b)

Nearside Front Front position lamp(s) not working (1.1.A.3b)

Nearside Rear Rear position lamp(s) not working (1.1.A.3b)

Rear Brake lever has restricted free movement (3.5.1k)

Rear Exhaust has a major leak of exhaust gases (7.1.2)

Speedometer cannot be illuminated. (6.7.3)

Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone 'A' (8.3.1e)

Windscreen washer provides insufficient washer liquid (8.2.3)

nearside front rolbar bush worn

offside front rollbar bush worn

rear radius arm bearings starting to deteriorate nearside

rear radius arm bearings starting to detreriorate offside

extensive welding repairs carried out ,various places ,covered with underseal,hard to access condition

Nearside Headlamp aim too high (1.8)

Nearside Headlamp insecure (1.7.3)

Nearside Rear position lamp(s) not working (1.1.A.3b)

extensive welding repairs carried out ,various places ,covered with underseal,hard to access condition

Play in steering rack inner joint(s)

Front registration plate letter/figure incomplete (6.3.1c)

Hazard warning switch faulty (1.4.B.1d)

Nearside Headlamp aim too high (1.8)

Nearside Headlamp insecure (1.7.3)

Offside Headlamp aim too high (1.8)

Offside Headlamp insecure (1.7.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Play in steering rack inner joint(s)

extensive welding repairs carried out on chassis /sills ,etc

n/s rear brake binding slightly

Brake pedal spongy (3.3.B.1b)

Front Brake master cylinder/servo mounting prescribed area is excessively corroded (3.6.C.3)

Nearside Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Nearside Inner Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Track rod end ball joint has excessive play (2.2.B.1f)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Track rod end ball joint has slight play (2.2.B.1f)

Offside Track rod end ball joint has slight play (2.2.B.1f)

Exhaust has part of the system slightly deteriorated (7.1.1a)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

o/s inner wing corroded but double skinned

slight footbrake travel

Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Nearside Side repeater insecure (1.4.A.2b)

Nearside Headlamp aim too low (1.8)

Offside Headlamp aim too low (1.8)

Brake pipe excessively corroded (3.6.B.2c)

Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Headlamp aim too low (1.8)

Nearside Rear Brake pipe excessively corroded (3.6.B.2c)

Nearside Rear Tyre fouling a part of the vehicle (4.1.D.2)

Nearside Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Nearside Side repeater missing (1.4.A.2b)

Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Headlamp aim not tested (1.8.A.1c)

Offside Headlamp insecure (1.7.3)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside Rear Tyre fouling a part of the vehicle (4.1.D.2)

Offside Side repeater missing (1.4.A.2b)

corrosion in nearside and offside outer cills

front number plate broken

slight free-play in nearside track rod/steering rack

Nearside Inner Front Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Nearside Outer Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Steering system has slight free play detected at steering wheel (2.2.A.1b)

Brakes imbalanced across an axle (3.7.B.5b)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Side repeater insecure (1.4.A.2b)

Offside Front constant velocity joint gaiter split (2.5.C.1a)

Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)

Nail in nearside rear tyre

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Inner Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Nearside Outer Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Offside Inner Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Steering system has slight free play detected at steering wheel (2.2.A.1b)

Nearside Front Side repeater not working (1.4.A.2c)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Front Side repeater not working (1.4.A.2c)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Parking brake lever has no reserve travel (3.1.6b)

Nearside Inner Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Inner Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Nearside Rear Brake hose slightly deteriorated (3.6.B.4d)

Offside Front Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Front constant velocity joint gaiter split (2.5.C.1a)

Nearside Front Brake hose excessively deteriorated (3.6.B.4d)

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Front Brake hose excessively deteriorated (3.6.B.4d)

Offside Rear Brake hose excessively deteriorated (3.6.B.4d)

Parking brake lever has no reserve travel (3.1.6b)

Nearside Rear Brake hose slightly deteriorated (3.6.B.4d)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)