1992 Rover 216

Emissions unable to be completed Engine Mis-fire (8.2.1.2 (d))

Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Trailing Arm (5.3.6 (a) (i))

Offside Rear Lower Suspension arm insecurely attached (5.3.3 (a) (i))

Offside Rear Suspension arm pin or bush excessively worn Trailing Arm (5.3.4 (a) (i))

Nearside Front Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Nearside Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement trailing arm (5.3.4 (a) (i))

Offside Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement trailing arm (5.3.4 (a) (i))

Coil spring corroded All (5.3.1 (b) (i))

Nearside Rear Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (1.4.2 (a) (i))

Service brake requirements only just met. It would appear that the braking system requires adjustment or repair (1.2.1 (c))

Under-body Components Covered In Under-seal

Nearside Rear Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i))

Nearside Rear Tyre has had the tread recut (5.2.3 (g))

Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Coil spring corroded All (5.3.1 (b) (i))

Nearside Rear Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (1.4.2 (a) (i))

Service brake requirements only just met. It would appear that the braking system requires adjustment or repair (1.2.1 (c))

catalyst faulty

Exhaust has a minor leak of exhaust gases (7.1.2)

Exhaust has part of the system slightly deteriorated (7.1.1a)

Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Exhaust has a minor leak of exhaust gases (7.1.2)

Outer Front Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Nearside Rear Brake pipe excessively corroded (3.6.B.2c)

Nearside Rear Brake pipe excessively corroded (3.6.B.2c)

Nearside Rear Registration plate lamp not working (1.1.5c)

Offside Front Brake pipe excessively corroded (3.6.B.2c)

Offside Rear Registration plate lamp not working (1.1.5c)

Exhaust has a minor leak of exhaust gases (7.1.2)

Front Tyre worn close to the legal limit (4.1.E.1)

Outer Front Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Brake pipe slightly corroded (3.6.B.2c)

Exhaust has a minor leak of exhaust gases (7.1.2)

Offside Front Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Nearside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

Brake pipe slightly corroded (3.6.B.2c)

Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Exhaust has a minor leak of exhaust gases (7.1.2)

Offside Front Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Rear Brake pipe slightly corroded (3.6.B.2c)

Brake pipe slightly corroded (3.6.B.2c)

Offside Rear Stop lamp not working (1.2.1b)

Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone 'A' (8.3.1b)