1992 Peugeot 106

Emissions not tested (7.0)

Exhaust emits visible black smoke at idle (7.3.A.2b)

Exhaust has a major leak of exhaust gases (7.1.2)

Exhaust system not adequately supported (7.1.1)

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Fuel system component insecure (7.2.1)

Nearside Front Headlamp insecure (1.7.3)

Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Nearside Rear Stop lamp not working (1.2.1b)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Front constant velocity joint gaiter insecurely mounted to its housing (2.5.C.1a)

Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Rear Spare wheel insecure (6.4.2)

Wheel insecure (4.2.A.1c)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Oil leak

Rear Radius arm has slight play in a pin/bush (2.4.G.2)

n/s/f inner cv gaitor split

o/s/f tyre age cracking

advanced corrosion rear chassis rails

advanced play in both track rod ends under load

deep cuts n/s front tyre

front and rear number plates poor

front tyres wearing low on inner edges

o/s front wheel heavily corroded

play in front seats

play n/s rear wheel bearing

welding repairs to both rear inner arches

severe corrosion to o/s rear wheel

Offside Rear fog lamp not working (1.3.2b)

Stop lamp remains on when the brakes are released (1.2.1e)

rear brake application uneven (3.7.B.2)

advanced corrosion rear chassis rails

advanced play in both track rod ends under load

deep cuts n/s front tyre

front and rear number plates poor

front tyres wearing low on inner edges

o/s front wheel heavily corroded

play in front seats

play n/s rear wheel bearing

welding repairs to both rear inner arches

severe corrosion to o/s rear wheel

Exhaust emissions hydrocarbon content excessive (7.3.B.1b)

Nearside Headlamp aim too low (1.8)

Nearside Rear Rear position lamp(s) adversely affected by the operation of another lamp (1.1.A.3f)

Nearside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Rear Tyre(s) incorrect because different size tyres are fitted on the same axle. (4.1.A.1a)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Headlamp aim too low (1.8)

Offside Rear An item not tested (Manual)

Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside rear brake binding (3.7.B.1)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Parking brake lever has no reserve travel (3.1.6b)

Parking brake: efficiency below requirements (3.7.B.7)

rear brake application uneven (3.7.B.2)

Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Nearside Rear wheel bearing has slight play (2.6.2)

engine missfire

n/s inner c v gaitor split

o/s parking brake cable outer casing split

slight roughness in n/s/r wheel bearing

suspension components corroded

uneven wear front tyres

Driver's seat insecure (6.2.A.1)

Exhaust emissions carbon monoxide content excessive (7.3.B.1a)

Offside Rear fog lamp not working (1.3.2b)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)

rear wiper blade and arm are missing

Nearside Front Front wheel bearing has excessive play (2.5.A.3c)

Offside Front Driver's seat insecure (6.2.A.1)

Rear Parking brake lever has no reserve travel (3.1.6b)

Rear Rear position lamp(s) adversely affected by the operation of another lamp (1.1.A.3f)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)