1993 Saab 900

Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))

Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength mount area (5.3.6 (a) (i))

Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill-floor/end of sill under wing (5.3.6 (a) (i))

Offside Rear Direction indicator adversely affected by the operation of another lamp (4.4.3 (b))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wing (5.3.6 (a) (i))

Brake pipe corroded, covered in grease or other material all rear (3) (1.1.11 (c))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Headlamp lens slightly defective both (4.1.1 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Power steering component has slight seepage from a component rack area (2.1.5 (a))

Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

n/s door step ,battery tray , o/s/f under wing, n/s/f chassis (rack mount area) and rear floors all corroding

o/s/f under wing and boot floor x3 all holed and corroded but in non pre scribed areas

Offside Rear Position lamp slightly affected by the operation of another lamp (4.2.3 (c))

slight corosion nearside floor non structural

Exhaust carbon monoxide content at idle exceeds manufacturer's specified limits co .65 (8.2.1.2 (b))

Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor/ jack point (6.1.1 (c) (i))

Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Rear Position lamp slightly affected by the operation of another lamp (4.2.3 (c))

Exhaust has a minor leak of exhaust gases middle (6.1.2 (a))

Nearside Rear Brake pipe corroded, covered in grease or other material as marked (1.1.11 (c))

Offside Rear Brake pipe corroded, covered in grease or other material as maked (1.1.11 (c))

Front Anti-roll bar pin or bush worn but not resulting in excessive movement both sides, outer bushes (5.3.4 (a) (i))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front Outer Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Offside Front Outer Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Power steering pipe(s) or hose(s) has slight seepage (2.3.3b)

Nearside Front Anti-roll bar linkage rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Anti-roll bar linkage rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Track rod end ball joint has slight play (2.2.B.1f)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone 'A' (8.3.1e)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Tyre has a bulge, caused by separation or partial failure of its structure (4.1.D.1b)

Parking brake lever has no reserve travel (3.1.6b)

rear brakes slightly out of balance

slight blow from exhaust

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

center exhaust box corroded and slightly blowing

front brake pads look low