2006 Chevrolet Matiz

Nearside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Shock absorbers has a reduced damping effect (5.3.2 (d))

Offside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Windscreen wiper blade defective (3.4 (b) (i))

Offside Rear Shock absorbers has a reduced damping effect (5.3.2 (d))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Brake pipe corroded, covered in grease or other material inner arch (1.1.11 (c))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Service brake binding but not excessively (1.2.1 (f))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Upper Shock absorbers has a slightly worn bush bush deteriorating (5.3.2 (c))

Nearside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting hole in sill (6.2.2 (d) (i))

Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Offside Rear Brake pipe excessively corroded (1.1.11 (c))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Brake pipe corroded, covered in grease or other material inner arch (1.1.11 (c))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Service brake binding but not excessively (1.2.1 (f))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Upper Shock absorbers has a slightly worn bush bush deteriorating (5.3.2 (c))

Central Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Outer Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Outer Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Oil leak, but not excessive (8.4.1 (a) (i))

Central Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Front Outer Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Outer Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced corrosion on both rear outer sills (6.1.1 (c) (i))

Offside Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Sub-frame corroded but not seriously weakened corrosion on rear subframe and assemblies (5.3.3 (b) (i))

both headlight lenses deteriorating

Exhaust has a minor leak of exhaust gases flexi pipe (7.1.2)

fuel filter rusty

Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt both fronts (2.5.C.1a)

Tyre worn close to the legal limit all four tyres getting low on tread and fronts perishing on walls (4.1.E.1)

Front Brake pad(s) wearing thin (3.5.1g)

NSF tyre wearing edges

OSF tyre wearing inner edge

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)