2007 Chevrolet Matiz

Brake lever has insufficient reserve travel (1.1.2 (a))

Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i))

Offside Front Anti-lock braking system component excessively damaged abs pick up ring (1.6 (e))

Offside Rear Brake pipe excessively corroded front to rear above fuel tank (1.1.11 (c))

Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i))

Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Nearside Front Inner Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Lower Suspension arm ball joint has slight play (5.3.4 (a) (i))

Nearside Front locking device missing on antiroll bar end and washer wrong way around

Nearside Rear Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))

Offside Front Inner Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Front Lower Suspension arm ball joint has slight play (5.3.4 (a) (i))

Offside Front antiroll bar locking device missing

Offside Front seatbelt twisted

Offside Rear Brake pipe corroded, covered in grease or other material from flexi to cylinder (1.1.11 (c))

corrosion on front brake back plates and insecure

corrosion on rear axle

Front Brake disc worn, pitted or scored, but not seriously weakened Both (1.1.14 (a) (ii))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement Perishing (5.3.4 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material To brake drum, corroded (1.1.11 (c))

Front Brake disc worn, pitted or scored, but not seriously weakened Both (1.1.14 (a) (ii))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement Perishing (5.3.4 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material To brake drum, corroded (1.1.11 (c))

Front Tyre worn close to legal limit/worn on edge both (5.2.3 (e))

corrosion to underside

Items removed from driver's view prior to test ()

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Rear axle corroded

both outer sills corrded

fuel tank straps corroded

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Front Mechanical brake component has restricted free movement brake binding (3.5.1k)

Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed (6.1.B.2)

Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

Items removed from driver's view prior to test ()

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Front brake slight bind

Rear axle corroded

both outer sills corrded

fuel tank straps corroded

Nearside Front Front position lamp(s) not working (1.1.A.3b)

Nearside Front Tyre has ply or cords exposed 155/65/13 (4.1.D.1b)

Offside Front Tyre has ply or cords exposed 155/65/13 (4.1.D.1b)

Fuel Filter Corroded

Front Exhaust system not adequately supported (7.1.1)

Offside Rear Mechanical brake component has restricted free movement (3.5.1k)

Front Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)