2009 Honda Accord

ACC, CMBS warning lights on

Offside Front Service brake binding but not excessively (1.2.1 (f))

Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Front Windscreen wiper does not clear the windscreen effectively split (3.4 (b) (ii))

ACC, CMBS warning lights on

Offside Front Service brake binding but not excessively (1.2.1 (f))

Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

ACC, LKAS,CMBS lights are on

Rear Integral body structure is corroded but structural rigidity is not significantly reduced rear sills are starting to corroded (6.1.1 (c) (i))

Rear Integral body structure is corroded but structural rigidity is not significantly reduced rear subframe mounting area corroded (6.1.1 (c) (i))

Rear Shock absorbers has a reduced damping effect (5.3.2 (d))

emissions to clean to test

Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c))

ACC, LKAS,CMBS lights are on

Rear Integral body structure is corroded but structural rigidity is not significantly reduced rear sills are starting to corroded (6.1.1 (c) (i))

Rear Integral body structure is corroded but structural rigidity is not significantly reduced rear subframe mounting area corroded (6.1.1 (c) (i))

Rear Parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (1.4.2 (a) (i))

Rear Shock absorbers has a reduced damping effect (5.3.2 (d))

emissions to clean to test

Nearside Front Windscreen wiper blade defective (3.4 (b) (i))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Windscreen wiper blade defective (3.4 (b) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Fuel cap/sealing device ineffective (6.1.3 (b) (i))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Nearside Front Windscreen wiper blade defective (3.4 (b) (i))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Windscreen wiper blade defective (3.4 (b) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Coil spring corroded both rear (5.3.1 (b) (i))

Nearside Rear Position lamp with a multiple light source up to 1/2 not functioning (4.2.1 (a) (i))

Nearside Front Headlamp lens slightly defective (4.1.1 (b) (i))

Offside Front Headlamp lens slightly defective (4.1.1 (b) (i))

Nearside Front Headlamp lens slightly defective (4.1.1 (b) (i))

Nearside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Offside Front Headlamp lens slightly defective (4.1.1 (b) (i))

Offside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Rear Tyre worn close to the legal limit worn on inner edge. (4.1.E.1)

Offside Rear wearing on inner edge.

Nearside Rear Tyre worn close to the legal limit worn on inner edge. (4.1.E.1)

Offside Rear wearing on inner edge.

Rear position lamp(s) not working (1.1.A.3b)

Front Tyre worn close to the legal limit (4.1.E.1)

Offside Rear position lamp(s) has light sources not illuminating, but not more than 50% (1.1.A.3b)

front brake pads very low

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Registration plate lamp not working (1.1.C.1d)

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)